{"id":36495,"date":"2024-03-28T11:46:28","date_gmt":"2024-03-28T10:46:28","guid":{"rendered":"https:\/\/3dwork.io\/?p=36495"},"modified":"2024-09-18T10:38:31","modified_gmt":"2024-09-18T09:38:31","slug":"twotrees-sk1-review","status":"publish","type":"post","link":"https:\/\/3dwork.io\/en\/twotrees-sk1-review\/","title":{"rendered":"TwoTrees SK1 : Review"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">Our colleagues at&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;have launched a very interesting new printer, the&nbsp;<strong>Twotrees SK1<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;is an old acquaintance in the 3D world, created in 2017 and launching its first 3D printer in 2018.&nbsp;In addition,&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;diversified its range of solutions back in 2020 by introducing the TT series of desktop diode laser engraving, which&nbsp;<a href=\"https:\/\/3dwork.io\/en\/twotrees-tts-55\/\">we could already see in our workshop<\/a>&nbsp;some time ago.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Today we are going to review their new&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;3D printer model that promises, on paper, a very fast printer with very interesting kinematics.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">As always before continuing with the article, remind you that you can join&nbsp;<strong>3DWork<\/strong>&nbsp;on our&nbsp;<a href=\"https:\/\/t.me\/trastornados\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>Telegram channel full of<\/strong><\/a>&nbsp;3D printing derangers, or on our social networks&nbsp;<a href=\"https:\/\/www.instagram.com\/3dwork.io\" class=\"external\" rel=\"nofollow\"><strong>Instagram<\/strong><\/a><strong>,<\/strong>&nbsp;<a href=\"https:\/\/www.youtube.com\/channel\/UCqCi3o3n9oWTZP9e6o8FN2w\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>YouTube<\/strong><\/a><strong>,&nbsp;<\/strong><a href=\"http:\/\/tiktok.com\/@3dwork.io\" class=\"external\" rel=\"nofollow\"><strong>TikTok<\/strong><\/a><strong>,&nbsp;<\/strong><a href=\"https:\/\/twitter.com\/3dwork_io\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>Twitter<\/strong><\/a>and<a href=\"https:\/\/www.facebook.com\/3DWork.Spain\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>Facebook<\/strong><\/a><strong>.<\/strong><\/p>\n\n\n\t\t\t\t<div class=\"wp-block-uagb-table-of-contents uagb-toc__align-left uagb-toc__columns-1 uagb-toc__collapse uagb-block-1557c8b6      \"\n\t\t\t\t\tdata-scroll= \"1\"\n\t\t\t\t\tdata-offset= \"30\"\n\t\t\t\t\tstyle=\"\"\n\t\t\t\t>\n\t\t\t\t<div class=\"uagb-toc__wrap\">\n\t\t\t\t\t\t<div class=\"uagb-toc__title\">\n\t\t\t\t\t\t\tTwoTrees SK1 &#8211; Index\t\t\t\t\t\t\t\t\t\t\t\t\t<svg xmlns=\"https:\/\/www.w3.org\/2000\/svg\" viewBox= \"0 0 384 512\"><path d=\"M192 384c-8.188 0-16.38-3.125-22.62-9.375l-160-160c-12.5-12.5-12.5-32.75 0-45.25s32.75-12.5 45.25 0L192 306.8l137.4-137.4c12.5-12.5 32.75-12.5 45.25 0s12.5 32.75 0 45.25l-160 160C208.4 380.9 200.2 384 192 384z\"><\/path><\/svg>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"uagb-toc__list-wrap \">\n\t\t\t\t\t\t<ol class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#twotrees-sk1\" class=\"uagb-toc-link__trigger\">TwoTrees SK1<\/a><li class=\"uagb-toc__list\"><a href=\"#contents-of-the-twotrees-sk1-kit\" class=\"uagb-toc-link__trigger\">Contents of the TwoTrees SK1 kit<\/a><li class=\"uagb-toc__list\"><a href=\"#twotrees-sk1-initial-installation\" class=\"uagb-toc-link__trigger\">TwoTrees SK1 Initial Installation<\/a><li class=\"uagb-toc__list\"><a href=\"#twotrees-sk1-component-analysis\" class=\"uagb-toc-link__trigger\">TwoTrees SK1 Component Analysis<\/a><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#chassis-kinematics\" class=\"uagb-toc-link__trigger\">Chassis &amp; Kinematics<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#extrusion-system-printing-platform\" class=\"uagb-toc-link__trigger\">Extrusion System &amp; Printing Platform<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#electronics\" class=\"uagb-toc-link__trigger\">Electronics<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#firmware-klipper\" class=\"uagb-toc-link__trigger\">Firmware Klipper<\/a><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#kiauh-klipper-installation-and-update-helper\" class=\"uagb-toc-link__trigger\">Kiauh (Klipper Installation And Update Helper)<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#fluidd-update\" class=\"uagb-toc-link__trigger\">Fluidd Update<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#backup-of-our-configuration-files\" class=\"uagb-toc-link__trigger\">Backup of our configuration files<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#add-mcu-temperature-report\" class=\"uagb-toc-link__trigger\">Add MCU Temperature Report<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#time-sync-update\" class=\"uagb-toc-link__trigger\">Time Sync &amp; Update<\/a><li class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#input-shaping-vibration-compensation\" class=\"uagb-toc-link__trigger\">Input Shaping (Vibration Compensation)<\/a><\/li><\/ul><\/li><\/ul><\/li><li class=\"uagb-toc__list\"><a href=\"#printing-and-usage-tests-of-the-twotrees-sk1\" class=\"uagb-toc-link__trigger\">Printing and usage tests of the TwoTrees SK1<\/a><li class=\"uagb-toc__list\"><a href=\"#twotrees-sk1-enclosure-kit\" class=\"uagb-toc-link__trigger\">TwoTrees SK1 enclosure kit<\/a><li class=\"uagb-toc__list\"><a href=\"#final-review-twotrees-sk1\" class=\"uagb-toc-link__trigger\">Final review TwoTrees SK1<\/a><li class=\"uagb-toc__list\"><a href=\"#where-to-buy-the-twotrees-sk1\" class=\"uagb-toc-link__trigger\">Where to buy the TwoTrees SK1?<\/a><\/ul><\/ul><\/ol>\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\n\n\n<h2 class=\"wp-block-heading\" id=\"twotrees-sk1\"><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#twotrees-sk1\"><\/a><strong>TwoTrees SK1<\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;is a new generation within the&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees range of 3D<\/strong><\/a>&nbsp;printers, an evolution of the SP range, improving in many aspects.<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"SK1| Printing the Future Ahead!\u26a1\ufe0f\ud83c\udf33\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/rPD4_m2NS1U?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Among its main features we can highlight:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1442\" height=\"497\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91.jpeg\" alt=\"- - -\" class=\"wp-image-36579\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91.jpeg 1442w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91-300x103.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91-1024x353.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91-768x265.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91-450x155.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-91-780x269.jpeg 780w\" sizes=\"auto, (max-width: 1442px) 100vw, 1442px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Up to 700 mm\/s print speed with 20000 mm\/s acceleration<\/strong>, with the recommended speed being an interesting 300 mm\/s and adjust the accelerations based on the vibration compensation tests (Input Shaper)<\/li>\n\n\n\n<li>Very robust chassis and kinematics, its&nbsp;<strong>CoreXY chassis\/kinematics<\/strong>&nbsp;with&nbsp;<strong>machined parts and linear guides as well as triple Z-axis<\/strong>&nbsp;that will allow us a perfect alignment<\/li>\n\n\n\n<li>A&nbsp;<strong>print volume of 256x<\/strong><em><strong>256x<\/strong><\/em><strong>256mm<\/strong><\/li>\n\n\n\n<li><strong>Automatic calibration assistants<\/strong>, 3-axis automatic bed leveling as well as leveling sensor for compensation by means of 36-point bed mesh and vibration compensation<\/li>\n\n\n\n<li><strong>Klipper<\/strong>&nbsp;firmware that will allow us to squeeze the most out of the machine<\/li>\n\n\n\n<li><strong>Direct extrusion system with double gear and a hotend of up to 300\u00ba of high flow<\/strong><\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">In the following table you can see the specifications that we will analyze later:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1600\" height=\"688\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86.jpeg\" alt=\"- - -\" class=\"wp-image-36563\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86.jpeg 1600w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-300x129.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-1024x440.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-768x330.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-1536x660.jpeg 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-450x194.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-86-780x335.jpeg 780w\" sizes=\"auto, (max-width: 1600px) 100vw, 1600px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"contenido-del-kit-twotrees-sk1\">Contents of the TwoTrees SK1 kit<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;comes in a very compact and very well protected packaging to prevent damage during transport.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In the&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>kit TwoTrees<\/strong><\/a><strong>&nbsp;has included everything necessary to carry out the assembly, first tests and maintenance of the machine<\/strong>&nbsp;and some accessories for the electronics that are appreciated.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-087d8f01 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FE68xHL6LBzXtgoWvAEF9%252Fimage.png%3Falt=media%26token=1b72a6ed-4b85-4d87-bf78-6de962e201d3&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=9d46c0c92ce889eac0b92320bdc21faafc8ebd8f956c3bfa995ae485cd77c4fe\" alt=\"- - -\" width=\"1720\" height=\"1290\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Going into a little more detail of the contents of the kit we will see a small roll of PLA filament from&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;to be able to use our machine from the first moment, cables, spare parts, tools, screws, USB with some tests\/profiles\/printer manual as well as eMMC and microSD adapter for electronics update tasks.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"575\" height=\"376\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-66.png\" alt=\"- - -\" class=\"wp-image-36533\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-66.png 575w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-66-300x196.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-66-450x294.png 450w\" sizes=\"auto, (max-width: 575px) 100vw, 575px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"instalacion-inicial-twotrees-sk1\">TwoTrees SK1 Initial Installation<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>TwoTrees SK1&nbsp;<\/strong>comes practically assembled, so the start-up process is really simple by following the&nbsp;<a href=\"https:\/\/www.mediafire.com\/file_premium\/nd447iy425ym0no\/SK1_%25E8%25AF%25B4%25E6%2598%258E%25E4%25B9%25A6_%25E8%258B%25B1%25E6%25B3%2595%25E4%25B8%25AD%25283.0%2529-%25E6%258E%2592%25E7%2589%2588.pdf\/file\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">manual<\/a>&nbsp;or video that&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;has created of the process.<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"SK1 | Unboxing and Intallation Tutorial\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/8dKkvJDcvd0?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">In any case, here are the steps for more details:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We start by removing the&nbsp;<strong>TwoTrees SK1&nbsp;<\/strong>from the box, inside the structure we find two boxes with the screen and accessories<\/li>\n\n\n\n<li>First, we remove the XY axis anchors that are located at both ends of the linear guide, as well as at the head<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"584\" height=\"324\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83.jpeg\" alt=\"- - -\" class=\"wp-image-36541\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83.jpeg 584w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-300x166.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-450x250.jpeg 450w\" sizes=\"auto, (max-width: 584px) 100vw, 584px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We will assemble the stand and connect the screen, once connected we will anchor it to the stand by sliding it from above on the stand.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"243\" height=\"106\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75.jpeg\" alt=\"- - -\" class=\"wp-image-36505\" title=\"- -\"><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We will install the Wifi antenna in the connector that we can find on the right side of the printer next to the connector and power switch and other USB inputs, Ethernet, etc.<\/li>\n\n\n\n<li>Finally, we will anchor the filament roll holder, which is also located on the right side.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Here are some images of the process that, as we have mentioned, is very simple and will not require more than 15 minutes.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-c67b8b68 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252F1TyOehnY68ALfoQGUCGK%252Fimage.png%3Falt=media%26token=36b7015b-8f7c-43bc-97c7-2140e0cfee5f&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=5249e823487ab4c480210c2fbaf9f8d6fbee00fa3f27c12a5d525fa8d6554b50\" alt=\"- - -\" width=\"1304\" height=\"1210\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Now that we have everything installed, it&#8217;s time to connect our&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;to the mains, let&#8217;s not forget to check that the source is adjusted to the voltage we use in our case using the switch that we can find on the left side, and start the start-up process.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This process is quite simple to follow thanks to the options available on the screen:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The first step once the system boots up will be to go to the Settings menu (gear icon at the bottom of the screen) and Calibrate where we will take the first&nbsp;<strong>Z-Tilt<\/strong>&nbsp;option.&nbsp;The Z-Tilt is the bed alignment assistant thanks to the 3 independent axes that we have and that is a great feature to highlight of this printer.&nbsp;Basically, and using the leveling sensor of the&nbsp;<strong>TwoTrees SK1<\/strong>, it will measure the deviations at the three anchor points of the bed to mechanically correct any deviation and that our bed is always perfectly level with respect to our XY axis.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"820\" height=\"246\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74.jpeg\" alt=\"- - -\" class=\"wp-image-36501\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74.jpeg 820w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-300x90.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-768x230.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-450x135.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-780x234.jpeg 780w\" sizes=\"auto, (max-width: 820px) 100vw, 820px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The next step will be to&nbsp;<strong>adjust the Z-offset<\/strong>, which although it is set at the factory it does not hurt to check it, in this case and within the same screen as the previous point the second option.&nbsp;This calibration will be done using the typical sheet and adjusting the height from the screen until our nozzle rubs against the paper, in the video below you can see it in more detail.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"822\" height=\"250\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82.jpeg\" alt=\"- - -\" class=\"wp-image-36539\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82.jpeg 822w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-300x91.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-768x234.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-450x137.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-780x237.jpeg 780w\" sizes=\"auto, (max-width: 822px) 100vw, 822px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The next step will be the&nbsp;<strong>meshing of our printing surface<\/strong>, which we will launch from the third option.&nbsp;The bed mesh is basically going to poll readings with the leveling sensor that is going to allow our firmware to have a map of possible deviations in the printing surface that it will use to compensate during printing and always have a perfect first layer.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"823\" height=\"249\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79.jpeg\" alt=\"- - -\" class=\"wp-image-36531\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79.jpeg 823w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79-300x91.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79-768x232.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79-450x136.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-79-780x236.jpeg 780w\" sizes=\"auto, (max-width: 823px) 100vw, 823px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>As the last calibration step we will perform the&nbsp;<strong>Input Shaper<\/strong>, which we will deal with in more detail later and which we advise you to review in detail, which can significantly improve the finish and quality of our prints.&nbsp;Basically, this vibration compensation performs an analysis by means of a sensor, accelerometer that is located in the print head, of the vibrations when making movements in a frequency range&#8230;&nbsp;With this analysis, it establishes some adjustments during printing to eliminate vibrations that later affect the finish of the prints as ghosting\/waves in the outer layers.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"824\" height=\"236\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78.jpeg\" alt=\"- - -\" class=\"wp-image-36527\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78.jpeg 824w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78-300x86.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78-768x220.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78-450x129.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-78-780x223.jpeg 780w\" sizes=\"auto, (max-width: 824px) 100vw, 824px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We&#8217;ll follow the options within Settings, but in this case we&#8217;ll go to Network, where we can&nbsp;<strong>adjust the WiFi settings&nbsp;<\/strong>so that our printer connects to our network and the Internet if necessary.&nbsp;The process is very simple, from the screen it will show us the available WiFi networks and when we tap on ours we will have to enter its password to be able to connect to it.&nbsp;If everything has worked correctly, it will show us the IP address that we can use later in other processes.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"822\" height=\"242\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76.jpeg\" alt=\"- - -\" class=\"wp-image-36511\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76.jpeg 822w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-300x88.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-768x226.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-450x132.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-780x230.jpeg 780w\" sizes=\"auto, (max-width: 822px) 100vw, 822px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Connection to the&nbsp;<strong>management web interface (Fluidd).<\/strong>&nbsp;With the printer connected to our network and the IP address, we can go from our computer, or any other device, and enter the IP address we obtained in the previous step into our web browser&#8230;&nbsp;You&#8217;ll see the management website of your&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;where you&#8217;ll have more control options than those available on the screen.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1704\" height=\"820\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77.png\" alt=\"- - -\" class=\"wp-image-36569\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77.png 1704w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-300x144.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-1024x493.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-768x370.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-1536x739.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-450x217.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-780x375.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-1600x770.png 1600w\" sizes=\"auto, (max-width: 1704px) 100vw, 1704px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Thanks to the connectivity options of our&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;by its Klipper firmware apart from the web interface, we will be able to send our parts directly from our laminator in a comfortable way.&nbsp;Depending on our laminator, this configuration is going to be done in different ways, in our case using&nbsp;<a href=\"https:\/\/github.com\/SoftFever\/OrcaSlicer\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>OrcaSlicer<\/strong><\/a>:<img loading=\"lazy\" decoding=\"async\" srcset=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=400&amp;dpr=1&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 400w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=400&amp;dpr=2&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 800w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=400&amp;dpr=3&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 1200w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=400&amp;dpr=4&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 1600w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=768&amp;dpr=1&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 768w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=768&amp;dpr=2&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 1536w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=768&amp;dpr=3&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 2304w, https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af 3072w\" width=\"1062\" height=\"438\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FpfEDe4rb34PhupsfpVB3%252Fimage.png%3Falt=media%26token=ebae8e8d-56ef-453c-abfc-f755ded4247e&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=9ef2f0324e07328690a0284808d57bd6514ca117d3ba2f5f07d4885384e7f1af\" alt=\"- - -\" title=\"- -\"><\/li>\n\n\n\n<li>Then, and as a last step before printing,&nbsp;<strong>we will proceed to load the filament into the extrusion system using the wizard<\/strong>&nbsp;we have.&nbsp;It&#8217;s very simple, we will load the filament inside the PTFE tube to the print head and select LOAD on the screen, it will heat the hotend and when it is at the right temperature it will load the filament&#8230;&nbsp;We advise you to apply a little pressure at the beginning on the filament to make sure that it meshes into the extruder.&nbsp;At the end of the process, make sure to remove the extruded filament!!<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"823\" height=\"298\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81.jpeg\" alt=\"- - -\" class=\"wp-image-36537\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81.jpeg 823w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81-300x109.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81-768x278.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81-450x163.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-81-780x282.jpeg 780w\" sizes=\"auto, (max-width: 823px) 100vw, 823px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">We&#8217;re ready to release our first impressions!!&nbsp;We attach a video of&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;with the whole process that can be of great help to you:<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"SK1 | Basic Tutorial\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/W36lK6-PkCU?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">In addition,&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;emphasizes the&nbsp;<strong>quality process of assembly and testing of its machines where they check up to 47 critical points<\/strong>&nbsp;of the&nbsp;<strong>TwoTrees SK1<\/strong>.<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"SK1 | The 47-point Factory Inspection\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/zG45xdj6j90?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"analisis-componentes-twotrees-sk1\">TwoTrees SK1 Component Analysis<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Before analyzing the results and experience with the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;we would like to do a more detailed review of its components.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"chasis-y-cinematica\"><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#chasis-y-cinematica\"><\/a>Chassis &amp; Kinematics<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If there&#8217;s one aspect where the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;excels, it&#8217;s its rugged all-metal chassis, and when we say fully it&#8217;s completely.&nbsp;This aspect is going to be tremendously important as it is going to provide us with a solid and lasting foundation for the kinematics of a performance to match.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-e9c80bfa wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252F9EgKj1oJrCECBEEFRXcj%252Fimage.png%3Falt=media%26token=bf23c69d-d379-44ae-a724-9855cbdb1634&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=57de909a4936eaad6b46913f2155db9c7baf4ae561ff5bdc94d07c54008a5644\" alt=\"- - -\" width=\"1298\" height=\"308\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Regarding the kinematics, we have to highlight its CoreXY format, which also has linear guides in each of its axes and a sensational independent triple Z system that, as we have already explained, will allow you to have an automatic bed leveling and together with its 36-point mesh system on it we will have an almost perfect and automatic leveling.&nbsp;All thanks to the inductive sensor embedded in the print head.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1441\" height=\"481\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80.jpeg\" alt=\"- - -\" class=\"wp-image-36535\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80.jpeg 1441w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-300x100.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-1024x342.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-768x256.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-450x150.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-780x260.jpeg 780w\" sizes=\"auto, (max-width: 1441px) 100vw, 1441px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">All the belt passages are all-metal as well as the XY bridge where the linear guide rests, we also have generous A\/B motors to move the CoreXY kinematics and simple but effective belt tensioners that will be very useful to fine-tune the vibration compensation system later.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-bb28501b wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FryZpqRRFqdsyPVg9DTYE%252Fimage.png%3Falt=media%26token=cf9410ea-f76f-4151-9fec-64d5e0a3da9c&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=9c020b27d46d1da14c16716d11af1acc2a26e13310e694e39134994f7407df33\" alt=\"- - -\" width=\"1167\" height=\"278\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">As we have told you, the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;has an infestable triple Z system, all our machines whenever possible like to modify Z for the installation of&nbsp;<a href=\"https:\/\/s.click.aliexpress.com\/e\/_DBtTPEz\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">F8-16M bearings<\/a>&nbsp;that will significantly reduce the weight of the set on the motor shaft and can cause problems.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">On the other hand, we also like to add a bearing (7mm) as a ball joint in the coupling that allows us to improve the linearity of the rods, providing better stability to the Z axis in this case.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-4663cfba wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FSTAK9oFHXmf9w9kTTIIa%252Fimage.png%3Falt=media%26token=f57cb384-7abb-44d4-b6d6-c309f312dc8c&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=b63a8aa926b9953cbc68d0b6b13b5a363a6e92e54e887b8e101cadbe7a5080cc\" alt=\"- - -\" width=\"1415\" height=\"470\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">If we take into account the cost and time in making this improvement with respect to the benefits we can obtain, it is more than advisable not only in this&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;but in any machine.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-58f0a7cf wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FXDpmut0RKez6ZEBkyhRS%252Fimage.png%3Falt=media%26token=c1d76ed9-c906-48ae-9f94-d63f82e933e0&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=ccd405572acc36bd64ad49658c31b3839cffd332f47b61ee4357c1427306d191\" alt=\"- - -\" width=\"1299\" height=\"287\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-6548c34\" data-v=\"2\" data-block-id=\"6548c34\"><style>.stk-6548c34{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-6548c34 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-6548c34-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-abf0591\" data-block-id=\"abf0591\"><style>.stk-abf0591{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-f85830e\" data-block-id=\"f85830e\"><style>.stk-f85830e .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-f85830e .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#ff6900 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-f85830e\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-f-85830-e-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-f-85830-e-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M504 256c0 136.997-111.043 248-248 248S8 392.997 8 256C8 119.083 119.043 8 256 8s248 111.083 248 248zm-248 50c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-e332933\" id=\"strong-strong-strong-important-strong-strong-strong\" data-block-id=\"e332933\"><p class=\"stk-block-heading__text\"><strong><strong><strong>IMPORTANT!!!<\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Although TwoTrees insists on its plan of 47 inspection points during manufacturing, we advise you, and this in general for any machine that comes pre-assembled from the factory, to review the tightening of screws and tensioning of belts.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-c1a7124c wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FLQ7EVJze2EP9qctTLkVE%252Fimage.png%3Falt=media%26token=d23f6c94-c2b1-45ab-961e-734d32ed45a0&amp;width=300&amp;dpr=4&amp;quality=100&amp;sign=0daeeb55a683fc63b0713d63329da09df2a89f2d3583ff336dcc85b3d15274a7\" alt=\"- - -\" width=\"900\" height=\"287\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In our case and when making the previous modification we saw how the tightening of some of the couplings of the Z axis, and others of the machine, were not correctly fixed.&nbsp;As an example that you can see in the previous photo, one of the Z axes during the first homen of the machine jumped out of the coupling.<\/p>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Another modification that we have seen as totally advisable, basically because we have had filament supply problems due to tensions due to the passage of PTFE, is to guide the PTFE with adapters on the outside of the XY axis chain.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-3e346a9c wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FfEhuA0NE97451v0ad4nn%252Fimage.png%3Falt=media%26token=97b89b05-c8b2-43dc-b47c-1652328c90bf&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=ec5725db2dfb39ba428da0b4f050a7d265e5ed2ff3e7fc7c8efe9f357e52b6f5\" alt=\"- - -\" width=\"1887\" height=\"785\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In our&nbsp;<a href=\"https:\/\/klipper.3dwork.io\/klipper\/empezamos\/velocidad-maxima\">tests of maximum speed<\/a>&nbsp;and maximum extrusion volume we have obtained good results perhaps limited by the extrusion\/filament system so it makes this&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;one of the best machines, in terms of chassis\/kinematics, that we have tested lately.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"sistema-de-extrusion-plataforma-de-impresion-y-sistema-de-calefaccion-en-cerramiento\">Extrusion System &amp; Printing Platform<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>TwoTrees SK1<\/strong>, with the model analysed that does not include an enclosure, does not look like a printer focused on the printing of technical filaments.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In any case<strong>, we can print materials such as PLA, PETG, ASA\/ABS<\/strong>&nbsp;(taking into account their peculiarities with respect to printing with an ideally controlled room temperature) since we will be able to reach 300\u00ba.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We have been&nbsp;<strong>pleasantly surprised when disassembling the print head, since apparently its hotend is &#8220;identical&#8221; to clones of those used by Bambu Labs, so apart from having a well-tested design, we can have access to a wide range of spare parts, including being able to install CHT nozzles that will improve the extrusion volumetry<\/strong>&nbsp;to be able to scratch a little more printing speed&#8230;&nbsp;In our tests we have obtained a range of 20-25mm3\/s.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">At the extrusion system level, we have&nbsp;<strong>a double gear system with direct extrusion, which will provide us with precision in the control and flow of filament,<\/strong>&nbsp;especially important for a machine designed to work at high speeds such as the&nbsp;<strong>TwoTrees SK1<\/strong>.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-0637b8dc wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FzcMmUjiChKHSVKMuCHSQ%252Fimage.png%3Falt=media%26token=0616f22a-2ad6-4dc2-9985-ac3ba3996af3&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=52eceaf769508f4ea0468d902bbbafb2c0a3053f7f086849c58b0b8cce003fbc\" alt=\"- - -\" width=\"1300\" height=\"310\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In terms of ventilation,&nbsp;<strong>we have 3 ventilators<\/strong>&#8230;&nbsp;the typical&nbsp;<strong>layer&nbsp;<\/strong>and we liked its performance and design of the nozzles, although its size is somewhat non-standard&#8230;&nbsp;a&nbsp;<strong>secondary one for cooling and anchored the cold area of the hotend (heatsink)<\/strong>&#8230;&nbsp;and finally, a third for the&nbsp;<strong>ventilation of the extrusion motor and the electronics<\/strong>&nbsp;that are incorporated in the print head and that we will talk about in more detail later.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-d641434e wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FwgJihn4uQvs5tfQUN5OE%252Fimage.png%3Falt=media%26token=6fc7204c-940c-41ba-a14c-f176a5a2a163&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=4ca8e15903bc0344f047dd5c6e5e3ec3188e4eac312c94aabbe4878c6a68b78d\" alt=\"- - -\" width=\"1301\" height=\"308\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Something we didn&#8217;t like very much, which you can see in the photo above, is the printhead covers.&nbsp;Although they are easy to disassemble as they only have 4 screws each, on the front the PTFE tube makes it difficult to disassemble and on the back the anchoring of the cable\/PTFE chain.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">As for the printing platform,&nbsp;<strong>we have a volume of 256*256*256mm<\/strong>&nbsp;as we already mentioned, the&nbsp;<strong>heated bed at 24v on a 3mm aluminum surface<\/strong>&nbsp;that rests in turn on a metal platform supported on the 3 independent axes mentioned above.&nbsp;In our bed mesh tests we have not seen any major deviations in its machining\/construction.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-afe5381d wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252F3K3ZVvLeOZyeS9g0p9rR%252Fimage.png%3Falt=media%26token=02551ca2-3dff-44ab-ac63-3cf4324c1da5&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=b6b42da1c5a897402ec109e3e111e3934ef845fc0ea112956818d7e385499151\" alt=\"- - -\" width=\"2119\" height=\"777\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Moving on to the printing surface, it&nbsp;<strong>includes a double-sided PEI magnetic surface (rough on one and smooth on the other)&nbsp;<\/strong>that has actually behaved wonderfully in all our prints.&nbsp;Regarding the heater, it&nbsp;<strong>promises to reach up to about 100\u00ba in addition<\/strong>, although the heating time has not been particularly fast, the heat distribution over the entire surface, as well as the thermal stability have been very good.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-6ad4015d wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FSEjLVjTcg5tdAes41vnN%252Fimage.png%3Falt=media%26token=8c4178c2-2976-432d-8bde-99465ea4e941&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=94445141bc791cf692ffeb7b37ab8e135c03384cbfd5e688cdb7c4cf652754f6\" alt=\"- - -\" width=\"2119\" height=\"709\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">We also liked the two small guide\/stop screws that we have so that we can easily and reliably align the PEI strap.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"electronica\"><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#electronica\"><\/a>Electronics<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Now we come to one of the points that, along with the firmware, has lowered the expectations we were having with this machine.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">On the&nbsp;<strong>TwoTrees SK1 we find an all-in-one electronics from MKS<\/strong>, similar to those seen lately in other machines analyzed and that we did not particularly like.&nbsp;In&nbsp;<strong>this electronics we have the Klipper host part and the printer management electronics integrated<\/strong>.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-033bb019 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FS1hB1m0caCSHkL2dkgCM%252Fimage.png%3Falt=media%26token=b28312b3-8f09-4258-9899-7e7bb8b3ddb3&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=583e456f9010ab602543ccbceab71b1376f7551cb2e1d09b8ae97dd2d8830895\" alt=\"- - -\" width=\"1629\" height=\"1476\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">All these&nbsp;<strong>electronics are located at the bottom of the machine<\/strong>, another aspect that we didn&#8217;t like basically because it is not very accessible on the one hand and on the other because we believe that for heat dissipation it is not the optimal position&#8230;&nbsp;in any case,&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;has placed several&nbsp;<strong>fans to avoid temperature-related problems<\/strong>.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-307ba2c8 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FQZIT50xqSG0lGmA9bQiF%252Fimage.png%3Falt=media%26token=d56f5c96-5741-456f-9075-6ec1431730c3&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=2f6c673f310acbbc6ebe296380eb62ddfed4c5f1252b2023b7d86235e4a2f2f5\" alt=\"- - -\" width=\"2119\" height=\"1093\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Let&#8217;s review your electronics<\/strong>:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>For the Klipper part<\/strong>, it uses electronics customized for&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;MKS SKIPR, with a&nbsp;<strong>Rockchip RK3328 processor, Quad-core Cortex-A53, 1.5Ghz<\/strong>, with&nbsp;<strong>two DDR3 RAM modules of 512 KB and we have 1 GB in total<\/strong>&#8230;&nbsp;While we haven&#8217;t had any performance issues in our use, it&#8217;s a bit of a fair setup.\n<ul class=\"wp-block-list\">\n<li><em><strong>Ethernet port<\/strong><\/em><em>&nbsp;for wired network<\/em><\/li>\n\n\n\n<li><strong>2 * USB Ports<\/strong><\/li>\n\n\n\n<li><strong>RJ11 port<\/strong>&nbsp;for serial accessory connection<\/li>\n\n\n\n<li><em><strong>Wifi 2.4Ghz<\/strong><\/em><\/li>\n\n\n\n<li><em><strong>EMMC of 8GB,<\/strong><\/em>&nbsp;<em>which is fair given that with the installation of Klipper about&nbsp;<\/em><em><strong>2GB is available for our gcodes, timelapses, etc<\/strong><\/em><em>&#8230;&nbsp;a component that may be interesting to improve or look for formulas to lighten the size of the distribution used by&nbsp;<\/em><strong>TwoTrees<\/strong><\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"809\" height=\"289\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59.png\" alt=\"- - -\" class=\"wp-image-36513\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59.png 809w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59-300x107.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59-768x274.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59-450x161.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-59-780x279.png 780w\" sizes=\"auto, (max-width: 809px) 100vw, 809px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"809\" height=\"152\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55.png\" alt=\"- - -\" class=\"wp-image-36499\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55.png 809w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55-300x56.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55-768x144.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55-450x85.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-55-780x147.png 780w\" sizes=\"auto, (max-width: 809px) 100vw, 809px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Within the main electronics itself we find&nbsp;<strong>the management part of the printer<\/strong>&nbsp;that uses an MCU&nbsp;<strong>STM32F401XC to 84MHz of flash memory.<\/strong>..&nbsp;while the MKS SKIPR usually uses a&nbsp;<em>slightly more powerful STM32F407 MCU.&nbsp;By mounting<\/em><strong>&nbsp;TMC2209 drivers to control the X, Y and Z axes<\/strong>&nbsp;that are mounted&nbsp;<strong>on the socket<\/strong>&nbsp;so that we can replace them in case of failure.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"811\" height=\"145\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58.png\" alt=\"- - -\" class=\"wp-image-36509\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58.png 811w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58-300x54.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58-768x137.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58-450x80.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-58-780x139.png 780w\" sizes=\"auto, (max-width: 811px) 100vw, 811px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Finally&nbsp;<strong>in the printhead we have another control electronics<\/strong>, connected by USB to the main electronics, with an MCU&nbsp;<strong>Toolhead<\/strong>&nbsp;is again a customization of the MKS THR for <a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a><em>,<\/em>&nbsp;it has a&nbsp;<strong>Raspberry Pi RP2240 processor&nbsp;<\/strong>where we have all the connectors for the components of the printhead as well as<strong>&nbsp;an accelerometer for vibration compensation and a free pin for what looks like the installation of an LED.<\/strong><\/li>\n<\/ul>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-4bb4630f wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FY4r7KTOjDjx6WIEh4zTD%252Fimage.png%3Falt=media%26token=13ae4fc0-1046-49d3-93a1-c9305d8281b1&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=22f739639a928a931375d7d535485d52f6b5da719eae58b41c49ecb91f93e1bb\" alt=\"- - -\" width=\"2119\" height=\"1003\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"806\" height=\"142\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57.png\" alt=\"- - -\" class=\"wp-image-36507\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57.png 806w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57-300x53.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57-768x135.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57-450x79.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-57-780x137.png 780w\" sizes=\"auto, (max-width: 806px) 100vw, 806px\" \/><\/figure>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-2521331\" data-v=\"2\" data-block-id=\"2521331\"><style>.stk-2521331{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-2521331 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-2521331-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-4bca426\" data-block-id=\"4bca426\"><style>.stk-4bca426{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-6318691\" data-block-id=\"6318691\"><style>.stk-6318691 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-6318691 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#ff6900 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-6318691\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-6318691-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-6318691-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M504 256c0 136.997-111.043 248-248 248S8 392.997 8 256C8 119.083 119.043 8 256 8s248 111.083 248 248zm-248 50c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-bf5fe38\" id=\"strong-strong-strong-important-strong-strong-strong\" data-block-id=\"bf5fe38\"><p class=\"stk-block-heading__text\"><strong><strong><strong>IMPORTANT!!!<\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">With regard to this electronic, that of the print head, we have encountered several problems of disconnections and consistency failures in its operation after a few days of continuous use affecting our prints.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-6fb6d69b wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FLIYA5Oe1ckKcbA1BOMVR%252Fimage.png%3Falt=media%26token=1a1fcdc7-2cbf-48d8-960c-db95834b6b93&amp;width=300&amp;dpr=4&amp;quality=100&amp;sign=5e917013cd9aa95693b6090f426f488225ac9f8a105e5adfaeb8c48271b8ce79\" alt=\"- - -\" width=\"865\" height=\"328\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In our case and having experience in similar electronics of other of our machines, as soon as these problems started we made a small mod to improve heat dissipation by installing a couple of larger heatsinks.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Although, as we mentioned before, we have a fan to cool this area due to the compactness of the print head and its location, together with the wiring, hinders the flow of air, reducing its effectiveness.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-0344aca5 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252F3CAGnDpVr1hgn6GGD59A%252Fimage.png%3Falt=media%26token=fbaaf407-84bc-42cc-8aac-b1fa1f326a07&amp;width=300&amp;dpr=4&amp;quality=100&amp;sign=bae0863db02f68484f47e18631faca54ad900421f9d0d9e63f1bf29a1b61fd94\" alt=\"- - -\" width=\"500\" height=\"1186\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">After making this modification we have had no problems in any of our prints, printing continuously for hours.<\/p>\n<\/div><\/div>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We also&nbsp;<strong>have a 4.3&#8243; screen&nbsp;<\/strong>of which we do not have much information, it looks like a Nextion\/TaoJingChi model, simply that communicates by serial port (\/dev\/ttyS1) with Klipper and that&nbsp;<strong>TwoTrees<\/strong>&nbsp;has integrated with modifications in Klipper with its own firmware.<br>In the case of the screen, it has a fairly simple but intuitive interface, we have found missing or flawed in many of its functions, as well as the lack of preview of our laminated parts that we hope&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;will take into account to solve them as soon as possible.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"2119\" height=\"715\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89.jpeg\" alt=\"- - -\" class=\"wp-image-36575\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89.jpeg 2119w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-300x101.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-1024x346.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-768x259.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-1536x518.jpeg 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-2048x691.jpeg 2048w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-450x152.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-780x263.jpeg 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-89-1600x540.jpeg 1600w\" sizes=\"auto, (max-width: 2119px) 100vw, 2119px\" \/><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"firmware-klipper\"><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#firmware-klipper\"><\/a>Firmware Klipper<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If in the electronic section we find some aspects to improve in the Klipper firmware section, we are in a similar situation that has not convinced us.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We&#8217;ve already told you that&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;has a custom distribution with certain limitations that we&#8217;ll talk about in detail later.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Going into the Klipper software part:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Armbian MKS distribution and customized by TwoTrees using an old &#8220;buster&#8221; version<\/strong>&nbsp;instead of the current &#8220;bullseye&#8221;<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"809\" height=\"289\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61.png\" alt=\"- - -\" class=\"wp-image-36517\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61.png 809w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61-300x107.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61-768x274.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61-450x161.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-61-780x279.png 780w\" sizes=\"auto, (max-width: 809px) 100vw, 809px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"810\" height=\"413\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56.png\" alt=\"- - -\" class=\"wp-image-36503\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56.png 810w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56-300x153.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56-768x392.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56-450x229.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-56-780x398.png 780w\" sizes=\"auto, (max-width: 810px) 100vw, 810px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Rather outdated versions of Klipper and components of it unfortunately<\/strong>:<\/li>\n<\/ul>\n\n\n\n<div class=\"wp-block-uagb-image aligncenter uagb-block-12f7fd1b wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-center\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FDufAmUeXC1qoHlIPqLbU%252Fimage.png%3Falt=media%26token=b9d6fc5c-29d4-459a-81dc-af235e13f16b&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=82fc73f53a00abd469f6d63b445fd7db48818acac7d79082982f85e4a44110e4\" alt=\"- - -\" width=\"400\" height=\"479\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-cdd91a4\" data-v=\"2\" data-block-id=\"cdd91a4\"><style>.stk-cdd91a4{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-cdd91a4 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-cdd91a4-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-315f286\" data-block-id=\"315f286\"><style>.stk-315f286{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-f794775\" data-block-id=\"f794775\"><style>.stk-f794775 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-f794775 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#cf2e2e !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-f794775\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-f-794775-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-f-794775-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M504 256c0 136.997-111.043 248-248 248S8 392.997 8 256C8 119.083 119.043 8 256 8s248 111.083 248 248zm-248 50c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-9c130d4\" id=\"strong-strong-strong-strong-strong-strong-strong-important-strong-strong-strong-strong-strong-strong-strong\" data-block-id=\"9c130d4\"><p class=\"stk-block-heading__text\"><strong><strong><strong><strong><strong><strong><strong>IMPORTANT!!!<\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<div class=\"wp-block-stackable-text stk-block-text stk-block stk-85f5b58\" data-block-id=\"85f5b58\"><style>.stk-85f5b58{border-top-left-radius:0px !important;border-top-right-radius:0px !important;border-bottom-right-radius:0px !important;border-bottom-left-radius:0px !important;overflow:hidden !important;margin-bottom:0px !important}<\/style><p class=\"stk-block-text__text\"><strong><strong>DO NOT UPGRADE ANY CORE COMPONENTS (KLIPPER\/MOONRAKER\/SYSTEM) AS THEY MAY BREAK TwoTrees CONFIGURATION AND CUSTOMIZATIONS AND RENDER THE SYSTEM UNUSABLE.<\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Access to&nbsp;<strong>the management web interface, Fluidd, via the URL http:\/\/IP_HOST<\/strong><\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1716\" height=\"798\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76.png\" alt=\"- - -\" class=\"wp-image-36567\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76.png 1716w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-300x140.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-1024x476.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-768x357.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-1536x714.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-450x209.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-780x363.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-76-1600x744.png 1600w\" sizes=\"auto, (max-width: 1716px) 100vw, 1716px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We have&nbsp;<strong>SSH access&nbsp;<\/strong>using any client and using the IP along with the username\/password in the following table.&nbsp;The<strong>&nbsp;installation of klipper seems to be inside the mks user and using a rather old configuration directory structure that will cause problems if we update or add Klipper components<\/strong>.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-table is-style-regular\"><table><thead><tr><th>rol<\/th><th>nombre usuario<\/th><th>contrase\u00f1a<\/th><\/tr><\/thead><tbody><tr><td>root<\/td><td>root<\/td><td>makerbase<\/td><\/tr><tr><td>user (or user2)<\/td><td>mks<\/td><td>makerbase<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1942\" height=\"476\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68.png\" alt=\"- - -\" class=\"wp-image-36547\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68.png 1942w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-300x74.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-1024x251.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-768x188.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-1536x376.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-450x110.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-780x191.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-68-1600x392.png 1600w\" sizes=\"auto, (max-width: 1942px) 100vw, 1942px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"2290\" height=\"250\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71.png\" alt=\"- - -\" class=\"wp-image-36553\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71.png 2290w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-300x33.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-1024x112.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-768x84.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-1536x168.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-2048x224.png 2048w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-450x49.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-780x85.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-71-1600x175.png 1600w\" sizes=\"auto, (max-width: 2290px) 100vw, 2290px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">In the configuration section of the printer.cfg we find an implementation with relatively simple macros that usually perform their task correctly, such as filament management when the filament sensor detects a lack of filament.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Although we would like to add functions such as the M600 for example, which is a standard nowadays when it comes to making filament changes, or other macros that provide extra functions that allow the user to get the full potential of Klipper.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Although we have a shortened and limited version of Klipper,&nbsp;<strong>having SSH access and access to certain pre-installed tools will allow us to improve some aspects of our TwoTrees SK1<\/strong>.<\/p>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-2cc58da\" data-v=\"2\" data-block-id=\"2cc58da\"><style>.stk-2cc58da{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-2cc58da .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-2cc58da-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-257d8f3\" data-block-id=\"257d8f3\"><style>.stk-257d8f3{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-e8577c2\" data-block-id=\"e8577c2\"><style>.stk-e8577c2 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-e8577c2 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-e8577c2\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-e-8577-c-2-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-e-8577-c-2-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-58f035b\" id=\"strong-strong-strong-firmware-upgrades-strong-strong-strong\" data-block-id=\"58f035b\"><p class=\"stk-block-heading__text\"><strong><strong><strong>FIRMWARE UPGRADES :<\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">A step that we advise you to do once you have checked that the machine as it comes from origin works correctly is to check your installed firmware version.&nbsp;In this&nbsp;<a href=\"https:\/\/youtu.be\/iCqQRrkTyWk?si=AZK3PJvMOh3MiGah\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">video you will be able to see the update process<\/a>&nbsp;as well as check what versions you currently have.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We have 3 firmwares in our&nbsp;<strong>Twotrees SK1<\/strong>:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Host Klipper, actualmente imagen eMMC v2.0.0.21 del 2023\/12\/21<\/li>\n\n\n\n<li>MCU electr\u00f3nica de control, v1.0.0 del 2023\/12\/22<\/li>\n\n\n\n<li>TFT\/Pantalla, v3.5 del 2023\/12\/26<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"512\" height=\"177\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77.jpeg\" alt=\"- - -\" class=\"wp-image-36521\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77.jpeg 512w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-300x104.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-77-450x156.jpeg 450w\" sizes=\"auto, (max-width: 512px) 100vw, 512px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">We have to say that it is a somewhat tedious process, but&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;includes all the necessary accessories to be able to carry out the process.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">On the other hand, we invite you to visit the&nbsp;<a href=\"https:\/\/twotrees3d.com\/twotrees-sk1-corexy-3d-printer\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees SK1 website<\/strong><\/a>&nbsp;to review new updates in the tutorials section.<\/p>\n<\/div><\/div>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"kiauh-klipper-installation-and-update-helper\">Kiauh (Klipper Installation And Update Helper)<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>We also have&nbsp;<\/strong><a href=\"https:\/\/github.com\/dw-0\/kiauh\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>Kiauh<\/strong><\/a><strong>&nbsp;pre-installed that we can launch by running&nbsp;<\/strong><code><strong>.\/kiauh\/kiauh.sh<\/strong><\/code>, it will probably ask us to update it:<\/p>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-fb603cd\" data-v=\"2\" data-block-id=\"fb603cd\"><style>.stk-fb603cd{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-fb603cd .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-fb603cd-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-e2db616\" data-block-id=\"e2db616\"><style>.stk-e2db616{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-a6a4d86\" data-block-id=\"a6a4d86\"><style>.stk-a6a4d86 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-a6a4d86 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-a6a4d86\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-a-6-a-4-d-86-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-a-6-a-4-d-86-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-6c06892\" id=\"if-you-are-new-to-klipper-strong-kiauh-is-a-set-of-scripts-for-the-management-of-klipper-installations-that-will-allow-us-to-manage-certain-complex-manual-actions-from-convenient-menus-in-a-simplified-way-strong\" data-block-id=\"6c06892\"><p class=\"stk-block-heading__text\">If you are new to Klipper,<strong>&nbsp;Kiauh is a set of scripts for the management of Klipper installations that will allow us to manage certain complex manual actions from convenient menus in a simplified way.<\/strong><\/p><\/div>\n<\/div><\/div>\n<\/div><\/div>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"646\" height=\"770\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-72.png\" alt=\"- - -\" class=\"wp-image-36555\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-72.png 646w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-72-252x300.png 252w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-72-450x536.png 450w\" sizes=\"auto, (max-width: 646px) 100vw, 646px\" \/><\/figure>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"actualizacion-fluidd\">Fluidd Update<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">As we have already mentioned, the Klipper system in&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;is very old and it is not advisable to update any of its critical components (Klipper and Moonraker), but in the case of the web interface it can usually be updated without problem to add some extra functionality.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">From SSH we will launch Kiauh&nbsp;<code><strong>.\/kiauh\/kiauh.sh<\/strong><\/code>, we will go to the Update section (2) and from there we will select Fluidd (4)&#8230;&nbsp;Kiauh will work his magic!!!<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"650\" height=\"914\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-67.png\" alt=\"- - -\" class=\"wp-image-36545\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-67.png 650w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-67-213x300.png 213w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-67-450x633.png 450w\" sizes=\"auto, (max-width: 650px) 100vw, 650px\" \/><\/figure>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"anadir-reporte-de-temperaturas-de-mcus\">Backup of our configuration files<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">Before going into modifications and even between them, we advise you to always have a backup of your configuration files.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">From the web interface, from the Configuration panel (1), we will see the Configuration Files section where we will choose all (2) and click on the create zip icon (3):<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"879\" height=\"617\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84.jpeg\" alt=\"- - -\" class=\"wp-image-36543\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84.jpeg 879w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84-300x211.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84-768x539.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84-450x316.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84-780x548.jpeg 780w\" sizes=\"auto, (max-width: 879px) 100vw, 879px\" \/><\/figure>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"anadir-reporte-de-temperaturas-de-mcus-1\">Add MCU Temperature Report<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">By default,&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a><strong>&nbsp;only includes the temperature of the enclosure, extruder and heated bed<\/strong>&nbsp;in its configuration.&nbsp;Again, taking into account the characteristics of the machine and<strong>in order to have the conditions of the components under control and to have references when jams occur, it is advisable to add the temperatures of the main electronics (host and MCU, since they are integrated) and the toolhead<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">To do this and within the printer.cfg we will locate the&nbsp;<code>[include MCU_ID.cfg]<\/code>, we will add this configuration below for the temperatures of the host and mcu of the main electronics:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n&#x5B;include MCU_ID.cfg]\n\n### 3DWORK - Temperatures host + \u03bccontroler\n&#x5B;temperature_sensor host]\nsensor_type: temperature_host\nmin_temp: 10\nmax_temp: 75\n\n&#x5B;temperature_sensor mcu]\nsensor_type: temperature_mcu\nmin_temp: 10\nmax_temp: 75\n```\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">We will continue to look for&nbsp;<code>[include MKS_THR.cfg]&nbsp;<\/code>in the same printer.cfg file where we will add the following after this line:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n&#x5B;include MKS_THR.cfg]\n\n### 3DWORK Toolhead Temperature\n&#x5B;temperature_sensor toolboard]\nsensor_type: temperature_mcu\nsensor_mcu: MKS_THR\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">If we have done the steps correctly, we will be able to see the temperatures of all the components from our interface and have them under control:<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"796\" height=\"571\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47.png\" alt=\"- - -\" class=\"wp-image-36471\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47.png 796w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47-300x215.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47-768x551.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47-450x323.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-47-780x560.png 780w\" sizes=\"auto, (max-width: 796px) 100vw, 796px\" \/><\/figure>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"actualizacion-horaria\">Time Sync &amp; Update<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">Since&nbsp;<strong>the electronics do not have a battery to maintain the time adjustments, it is ideal that we configure the system to do it automatically<\/strong>.&nbsp;It is important because&nbsp;<strong>in this way we will have correct estimates of printing times, in addition to being able to make software updates over the internet<\/strong>.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"853\" height=\"352\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64.png\" alt=\"- - -\" class=\"wp-image-36525\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64.png 853w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64-300x124.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64-768x317.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64-450x186.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-64-780x322.png 780w\" sizes=\"auto, (max-width: 853px) 100vw, 853px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The process is very simple by launching the following commands:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>First of all, we&#8217;ll adjust our time zone with the following commands:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\ntimedatectl list-timezones # to list available time zones\nsudo timedatectl set-timezone Europe\/Madrid # to set Europe\/Madrid timezone\ntimedatectl # to check timezone was ok\n<\/pre><\/div>\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1498\" height=\"308\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63.png\" alt=\"- - -\" class=\"wp-image-36523\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63.png 1498w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63-300x62.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63-1024x211.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63-768x158.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63-450x93.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-63-780x160.png 780w\" sizes=\"auto, (max-width: 1498px) 100vw, 1498px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We&#8217;ll disable&nbsp;<code>systemd-timesync<\/code>:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\nsystemctl status systemd-timesyncd # to check current status\nsystemctl stop systemd-timesyncd # to stop systemd-timesyncd daemon\nsystemctl disable --now systemd-timesyncd.service # to disable systemd-timesyncd daemon\nsystemctl status systemd-timesyncd # to check systemd-timesyncd is disabled\n<\/pre><\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>We&#8217;ll install&nbsp;<code>chrony<\/code>:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\nsudo apt install chrony -y # to install chrony\n<\/pre><\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>We&#8217;ve restarted the service:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\nsudo systemctl restart chronyd # to restart chrony daemon\n<\/pre><\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>We can check the settings in case we want to adjust something, it is usually not necessary:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\nsudo nano \/etc\/chrony\/chrony.conf\n<\/pre><\/div>\n\n\n<ul class=\"wp-block-list\">\n<li>We check the synchronization status with these commands:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\nchronyc sources\nchronyc tracking\n<\/pre><\/div>\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"1016\" height=\"682\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48.png\" alt=\"- - -\" class=\"wp-image-36473\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48.png 1016w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48-300x201.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48-768x516.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48-450x302.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-48-780x524.png 780w\" sizes=\"auto, (max-width: 1016px) 100vw, 1016px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">We can run a&nbsp;<code>date<\/code>&nbsp;command to verify that everything is in sync.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Now, when you turn off your machine, it will adjust the time when it starts.<\/p>\n\n\n\n<h4 class=\"wp-block-heading\" id=\"input-shaping-compensacion-vibraciones\">Input Shaping (Vibration Compensation)<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">The Input Shaper process carried out by&nbsp;<strong>TwoTrees<\/strong>&nbsp;is totally unassisted, which is fine because you don&#8217;t have to do anything but, on the other hand, you have the problem that you don&#8217;t know how your machine really feels or how to try to adjust it optimally.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In the following video you can see the default process:<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"Two Trees SK1   How to calibrate vibration compensation values Input Shaper?\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/ouw0qpqQsbA?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">We&#8217;re going to improve the process to be able to generate the graphs and be able to see the result of the Input Shaper.<\/p>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-4e5ebcd\" data-v=\"2\" data-block-id=\"4e5ebcd\"><style>.stk-4e5ebcd{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-4e5ebcd .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-4e5ebcd-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-47ee2d6\" data-block-id=\"47ee2d6\"><style>.stk-47ee2d6{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-7cb57c8\" data-block-id=\"7cb57c8\"><style>.stk-7cb57c8 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-7cb57c8 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-7cb57c8\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-7-cb-57-c-8-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-7-cb-57-c-8-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-0ba620f\" id=\"to-be-able-to-perform-this-procedure-we-need-the-klipper-g-code-shell-command-extension-this-extension-is-already-installed-on-the-strong-two-trees-sk-1-strong\" data-block-id=\"0ba620f\"><p class=\"stk-block-heading__text\">To be able to perform this procedure we need the Klipper G-Code Shell Command extension, this extension is already installed on the&nbsp;<strong>TwoTrees SK1<\/strong>.<\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"has-text-align-left wp-block-paragraph\">If you don&#8217;t have it from Kiauh, you&#8217;ll install G-Code Shell Command, Advanced (4) and G-Code Shell Command (8)&#8230;&nbsp;<strong>it will first ask us if we want to install the extension and we will say Yes<\/strong>,&nbsp;<strong>second it will ask if you create a gcode shell example and we will say No<\/strong><\/p>\n<\/div><\/div>\n\n\n\n<ul class=\"wp-block-list\">\n<li>We will go to our web interface and within the CONFIGURATION section of Fluidd we will create a new&nbsp;<code>shell_command.cfg<\/code>:<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"889\" height=\"268\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60.png\" alt=\"- - -\" class=\"wp-image-36515\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60.png 889w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60-300x90.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60-768x232.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60-450x136.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-60-780x235.png 780w\" sizes=\"auto, (max-width: 889px) 100vw, 889px\" \/><\/figure>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Within&nbsp;<code>shell_command.cfg<\/code>&nbsp;we will include the following shell macros:<\/li>\n<\/ul>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n&#x5B;respond]\n### 3DWORK - Input Shaper csv-&gt;png\n&#x5B;gcode_macro SHAPER_CALIBRATE_XY]\ndescription: process csv file to png\ngcode:\n    RESPOND MSG=&quot;Homing&quot;\n    G28\n    RESPOND MSG=&quot;Testing Input Shaper XY!&quot;\n    SHAPER_CALIBRATE\n    RESPOND MSG=&quot;Generating Input Shaper X Graphs!&quot;\n    RESPOND MSG=&quot;Generating Input Shaper Y Graphs!&quot;\n    RUN_SHELL_COMMAND CMD=adxl_x\n    RUN_SHELL_COMMAND CMD=adxl_y\n    RESPOND MSG=&quot;Input shaper graphs generated for X and Y. You&#039;ll find them in your config\/input_shaper folder in the CONFIGURATION tab!&quot;\n  \n&#x5B;gcode_shell_command adxl_x]\ncommand: sh \/home\/mks\/klipper_config\/shell_commands\/adxl_x.sh \ntimeout: 300.\nverbose: True\n\n&#x5B;gcode_shell_command adxl_y]\ncommand: sh \/home\/mks\/klipper_config\/shell_commands\/adxl_y.sh \ntimeout: 300.\nverbose: True\n\n&#x5B;gcode_macro SHAPER_CALIBRATE_COREXY_BELT_TENSION]\ndescription: Generates resonance graph used to ensure belts are equally tensioned.\ngcode:\n    RESPOND MSG=&quot;Homing!&quot;\n    G28\n    RESPOND MSG=&quot;Testing Upper Belt!&quot;\n    TEST_RESONANCES AXIS=1,1  OUTPUT=raw_data NAME=belt-tension-upper\n    RESPOND MSG=&quot;Testing Lower Belt!&quot;\n    TEST_RESONANCES AXIS=1,-1 OUTPUT=raw_data NAME=belt-tension-lower\n    RESPOND MSG=&quot;Generating Input Shaper Belt Tension Graphs!&quot;\n    RUN_SHELL_COMMAND CMD=adxl_belt\n    RESPOND MSG=&quot;Belt tension graphs generated. You&#039;ll find them in your config\/input_shaper folder in the CONFIGURATION tab!&quot;\n\n&#x5B;gcode_shell_command adxl_belt]\ncommand: sh \/home\/mks\/klipper_config\/shell_commands\/adxl_belt.sh \ntimeout: 300.\nverbose: True\n\n### 3DWORK - Backup config to Github\n### https:\/\/klipper.3dwork.io\/klipper\/mejoras\/backup-klipper\n&#x5B;gcode_shell_command backup_cfg]\ncommand: sh \/home\/mks\/klipper_config\/shell_commands\/autocommit.sh\ntimeout: 30.\nverbose: True\n\n&#x5B;gcode_macro BACKUP_CFG]\ngcode:\n    RUN_SHELL_COMMAND CMD=backup_cfg\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">We&#8217;ll go to our web interface and within the CONFIGURATION section of Fluidd we&#8217;ll create a folder called shell_commands:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"877\" height=\"294\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65.png\" alt=\"- - -\" class=\"wp-image-36529\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65.png 877w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65-300x101.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65-768x257.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65-450x151.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-65-780x261.png 780w\" sizes=\"auto, (max-width: 877px) 100vw, 877px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Inside this folder we will add a file called&nbsp;<code>adxl_x.sh<\/code>&nbsp;with the following content:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n#!\/bin\/bash\n\nNEWX=$(ls -Art \/tmp\/calibration_data_x_*.csv | tail -n 1)\nDATE=$(date +&#039;%Y-%m-%d-%H%M%S&#039;)\n\noutdir=\/home\/mks\/klipper_config\/input_shaper\nif &#x5B; ! -d &quot;${outdir}&quot; ]; then\n    mkdir &quot;${outdir}&quot;\nfi\n\n\/home\/mks\/klipper\/scripts\/calibrate_shaper.py $NEWX -o &quot;${outdir}\/resonances_x_$DATE.png&quot;\n\nrm \/tmp\/calibration_data_x_*.csv\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">We will add a second file called&nbsp;<code>adxl_y.sh<\/code>&nbsp;with the following content:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n#!\/bin\/bash\n\nNEWX=$(ls -Art \/tmp\/calibration_data_y_*.csv | tail -n 1)\nDATE=$(date +&#039;%Y-%m-%d-%H%M%S&#039;)\n\noutdir=\/home\/mks\/klipper_config\/input_shaper\nif &#x5B; ! -d &quot;${outdir}&quot; ]; then\n    mkdir &quot;${outdir}&quot;\nfi\n\n\/home\/mks\/klipper\/scripts\/calibrate_shaper.py $NEWX -o &quot;${outdir}\/resonances_y_$DATE.png&quot;\n\nrm \/tmp\/calibration_data_y_*.csv\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">We will add a third file called&nbsp;<code>adxl_belt.sh<\/code>&nbsp;with the following content:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n#!\/bin\/bash\n#set -e -u -o pipefail\n\n## the TEST_RESONANCES command seems to return before all data is completely\n## written. it&#039;d be better to poll for the files to be completely written,\n## but this has been reliable for me so far\u2026\nsleep 10\n\noutdir=\/home\/mks\/klipper_config\/input_shaper\nif &#x5B; ! -d &quot;${outdir}&quot; ]; then\n    mkdir &quot;${outdir}&quot;\nfi\n\n\/home\/mks\/klipper\/scripts\/graph_accelerometer.py \\\n    -c \/tmp\/*.csv \\\n    -o &quot;${outdir}\/belt-tension-resonances-$( date +&#039;%Y-%m-%d-%H%M%S&#039; ).png&quot;\n\nrm \/tmp\/raw_data_axis*\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">Inside our printer.cfg we will add an include to load our new shell_command.cfg at the end of it, but&nbsp;<strong>remember that as always above the section SAVE_CONFIG!!!<\/strong>:<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n### 3DWORK - Shell Macros\/Commands\n&#x5B;include shell_command.cfg]\n\n#*# &amp;lt;---------------------- SAVE_CONFIG ----------------------&gt;\n<\/pre><\/div>\n\n\n<p class=\"wp-block-paragraph\">We will restart our Klipper and we will have to find a new macro SHAPER_CALIBRATE_XY that we can launch and it will perform a homing process, test in XY of Input Shaper and generate the graphs to be able to review them:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1633\" height=\"457\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69.png\" alt=\"- - -\" class=\"wp-image-36549\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69.png 1633w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-300x84.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-1024x287.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-768x215.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-1536x430.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-450x126.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-780x218.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-69-1600x448.png 1600w\" sizes=\"auto, (max-width: 1633px) 100vw, 1633px\" \/><\/figure>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-ad34f95\" data-v=\"2\" data-block-id=\"ad34f95\"><style>.stk-ad34f95{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-ad34f95 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-ad34f95-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-c7fc6e2\" data-block-id=\"c7fc6e2\"><style>.stk-c7fc6e2{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-151314f\" data-block-id=\"151314f\"><style>.stk-151314f .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-151314f .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#fcb900 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-151314f\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-151314-f-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-151314-f-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M504 256c0 136.997-111.043 248-248 248S8 392.997 8 256C8 119.083 119.043 8 256 8s248 111.083 248 248zm-248 50c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-a8dc79c\" id=\"strong-strong-strong-strong-strong-strong-strong-important-strong-strong-strong-strong-strong-strong-strong\" data-block-id=\"a8dc79c\"><p class=\"stk-block-heading__text\"><strong><strong><strong><strong><strong><strong><strong>IMPORTANT!!!<\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">The macro SHAPER_CALIBRATE_XY created by us uses the Klipper&nbsp;<a href=\"https:\/\/klipper.3dwork.io\/klipper\/empezamos\/input-shaper#ajuste-automatico-de-valores-de-resonancia-por-klipper\">macro SHAPER_CALIBRATE<\/a>&#8230;&nbsp;this means that it does the Input Shaving test, automatically selects the configuration it thinks is most appropriate, and applies it to the configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Although this is the most comfortable, sometimes it is not optimal, so we advise you to check the&nbsp;<a href=\"https:\/\/klipper.3dwork.io\/klipper\/empezamos\/input-shaper\">Input Shaper guide<\/a>&nbsp;for more details if you notice that our result graphs are not optimal.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">On the other hand, before carrying out the process and after it, it is more than advisable to do maintenance of our machine, this maintenance will be carried out in relation to checking that all the screws and anchors of the chassis and kinematics are correctly in their tightening, in addition to lubricating<\/p>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">You&#8217;ll find the generated graphs in a new folder in our \/config called input_shaper:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1679\" height=\"459\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73.png\" alt=\"- - -\" class=\"wp-image-36557\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73.png 1679w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-300x82.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-1024x280.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-768x210.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-1536x420.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-450x123.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-780x213.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-73-1600x437.png 1600w\" sizes=\"auto, (max-width: 1679px) 100vw, 1679px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Inside you will find the graphs of each axis:<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1689\" height=\"453\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74.png\" alt=\"- - -\" class=\"wp-image-36561\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74.png 1689w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-300x80.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-1024x275.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-768x206.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-1536x412.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-450x121.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-780x209.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-74-1600x429.png 1600w\" sizes=\"auto, (max-width: 1689px) 100vw, 1689px\" \/><\/figure>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-d781ac25 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FaV6yMF4VioJ6APQbL8vP%252Fimage.png%3Falt=media%26token=5b8ebaee-84cd-4bf7-90b3-137a1cc52329&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=ae55e43c710cebebbb505ecaf4eb1e19803e1f9d37b44795546119acd27692fe\" alt=\"- - -\" width=\"798\" height=\"598\" title=\"- -\" loading=\"lazy\" role=\"img\"><figcaption class=\"uagb-image-caption\">X-axis Input Shaper Chart&#8230;\u00a0<br>Although it can be improved, it&#8217;s not bad at all<\/figcaption><\/figure><\/div>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-3bdd8d1f wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FtawhEevsb3LIJuhoTIPR%252Fimage.png%3Falt=media%26token=2d7d5e39-c0fd-4d7a-9a4e-38f6367edd39&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=38e72a23e5953fb34e07be7bef5a8888200b4af58c8ea27bb0503e9c4dd4dc61\" alt=\"- - -\" width=\"798\" height=\"599\" title=\"- -\" loading=\"lazy\" role=\"img\"><figcaption class=\"uagb-image-caption\">Graphic Input Shaper Y-axis&#8230;\u00a0<br>Here we see that there is some more work<\/figcaption><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">As you can see in the example above, there is a lot of room for improvement!!&nbsp;If you want&nbsp;<a href=\"https:\/\/klipper.3dwork.io\/klipper\/empezamos\/input-shaper#como-interpretar-los-resultados\">to learn how to interpret them, you can find information in our Input Shaper guide<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Let&#8217;s start by looking at the tension of our belts using the new macro SHAPER_CALIBRATE_COREXY_BELT_TENSION which will perform a similar process to the previous one but will show us a graph of the tension of the belts to have a reference.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1624\" height=\"449\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75.png\" alt=\"- - -\" class=\"wp-image-36565\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75.png 1624w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-300x83.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-1024x283.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-768x212.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-1536x425.png 1536w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-450x124.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-780x216.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-75-1600x442.png 1600w\" sizes=\"auto, (max-width: 1624px) 100vw, 1624px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"799\" height=\"598\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70.png\" alt=\"- - -\" class=\"wp-image-36551\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70.png 799w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-300x225.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-768x575.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-280x210.png 280w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-560x420.png 560w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-450x337.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-70-780x584.png 780w\" sizes=\"auto, (max-width: 799px) 100vw, 799px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Now we will show you, in practice, how these tests will help us to significantly improve the performance and quality of our machine.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We&#8217;ll start with the belt graphs, basically in our case what we did was homing all the axes and we moved the Y axis to its 0 coordinate.&nbsp;With a Spectroid-style mobile application that analyzes the sound we will try to adjust that the frequency in both straps in the middle of their lateral travel gives us a frequency of about 75-85Hz, we can also use touch or ear to make this first adjustment since later with the graphics we will play with the adjustments.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The goal is to obtain a graph of overlapping belts as much as possible!!&nbsp;You don&#8217;t have to be paranoid about them being exact, but you do have to be paranoid that they overlap as much as possible and that the peak of these is of the similar high frequency.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">As you can see, the peak is at a desirable 50Hz, as well as having much less variation in responses.&nbsp;So our goal is to try to correct the tension of the upper step belt (orange) so that it assimilates to the lower one (blue).<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-a9b8c7d5 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FTbufHmYFs4ceUuVR6DVD%252Fimage.png%3Falt=media%26token=0abc7d17-da5a-4713-bad9-35562137b092&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=61d80fa881ac91d23c44aa6de81f3284e9e98a8422f1aaa9f25d08e5733101b2\" alt=\"- - -\" width=\"1599\" height=\"586\" title=\"- -\" loading=\"lazy\" role=\"img\"><figcaption class=\"uagb-image-caption\">Right before and left after adjusting these&#8230;\u00a0<br>The change has been substantial.<\/figcaption><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In the following video we can see the process for adjusting belt tension on our&nbsp;<strong>TwoTrees SK1<\/strong>:<\/p>\n\n\n\n<figure class=\"wp-block-embed is-type-video is-provider-youtube wp-block-embed-youtube wp-embed-aspect-16-9 wp-has-aspect-ratio\"><div class=\"wp-block-embed__wrapper\">\n<iframe loading=\"lazy\" title=\"Two Trees SK1   How to adjust the synchronous belt tensioner?\" width=\"1170\" height=\"658\" src=\"https:\/\/www.youtube.com\/embed\/67vkRYJgc0s?feature=oembed\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen><\/iframe>\n<\/div><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">But what do we get with this?&nbsp;Now we&#8217;ll see it in the following graphs when we relaunch the macro SHAPER_CALIBRATE_XY and we&#8217;ll analyze the results again&#8230;&nbsp;Let&#8217;s start with the X axis:<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-01088ff3 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252F6zMFo54JWYTMiW1WudJD%252Fimage.png%3Falt=media%26token=a2116651-df5d-4712-bb06-0220391ff4e1&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=643fde267b3059bc5e41f1a9c18f3a21e3622fb4992d7fe924ed82079bf8f880\" alt=\"- - -\" width=\"1599\" height=\"586\" title=\"- -\" loading=\"lazy\" role=\"img\"><figcaption class=\"uagb-image-caption\">Left original state, right once adjusted<\/figcaption><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In this case, with the moderately correct adjustment of our straps, we have gone to a much cleaner vibration graph with a well-marked peak of frequencies and in high frequencies, which is great.&nbsp;In addition, the suggested type of Input Shaper is the same but with significantly higher accelerations as well as fairly good vibration and smooth ranges.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Let&#8217;s also review the Y-axis graph:<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-ddbaa9d1 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252Fo5T4zoh1pDFSo1QFJ6CP%252Fimage.png%3Falt=media%26token=3cc4257b-2bdf-4d88-8825-35399e616c71&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=f918c3e757c0bb810808389597fc379e0e5b41bc1b9855642c4afabc65912509\" alt=\"- - -\" width=\"1599\" height=\"587\" title=\"- -\" loading=\"lazy\" role=\"img\"><figcaption class=\"uagb-image-caption\">Left original state, right once adjusted<\/figcaption><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">In this case, although the original graphics were not bad, it has been significantly improved again, a better type of Input Shaper suggested, a significant increase in accelerations and very good vibration\/smooth values.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We can already save these Input Shaper values and in the case of maximum accelerations it is advisable to select the value that does not exceed the values calculated on the X and Y axes (we will use the lowest of them) in addition to adding a certain margin of safety such as 90-95% of the value we obtained in the tests (again on the axis that gave us the lowest value).&nbsp;In the same way, we will adjust max_accel_to_decel to 1\/2 of the previous value.<\/p>\n\n\n<div class=\"wp-block-syntaxhighlighter-code \"><pre class=\"brush: plain; title: ; notranslate\" title=\"\">\n&#x5B;input_shaper]\nshaper_freq_x: 84.0\nshaper_freq_y: 56.0\nshaper_type_x: mzv\nshaper_type_y: zv\n\n&#x5B;printer]\nkinematics:corexy\nmax_velocity: 800\nmax_accel: 12000\nmax_accel_to_decel: 6000\nmax_z_velocity: 15\nmax_z_accel: 100\nsquare_corner_velocity: 5.0\n<\/pre><\/div>\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-4a0198a\" data-v=\"2\" data-block-id=\"4a0198a\"><style>.stk-4a0198a{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-4a0198a .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-4a0198a-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-e16e99f\" data-block-id=\"e16e99f\"><style>.stk-e16e99f{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-4c60257\" data-block-id=\"4c60257\"><style>.stk-4c60257 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-4c60257 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#fcb900 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-4c60257\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-4-c-60257-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-4-c-60257-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M504 256c0 136.997-111.043 248-248 248S8 392.997 8 256C8 119.083 119.043 8 256 8s248 111.083 248 248zm-248 50c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-d8fda5b\" id=\"strong-strong-remember-that-as-we-mentioned-the-input-shaper-macros-both-original-and-those-created-by-us-will-directly-configure-the-values-recommended-by-them-in-our-printer-cfg-strong-strong-br-strong-strong-so-if-we-carry-out-these-tests-we-must-save-them-from-the-web-ui-option-or-if-we-have-put-some-by-hand-we-must-make-sure-to-adjust-them-correctly-afterwards-strong-strong-br-strong-strong-these-adjustments-by-the-macros-do-not-cover-the-max-accel-and-max-accel-to-decel-settings-so-in-this-case-we-always-have-to-adjust-them-manually-strong-strong\" data-block-id=\"d8fda5b\"><p class=\"stk-block-heading__text\"><strong><strong>Remember that, as we mentioned, the Input Shaper macros, both original and those created by us, will directly configure the values recommended by them in our printer.cfg.<\/strong><\/strong><br><strong><strong>So if we carry out these tests we must save them from the web UI option, or if we have put some by hand we must make sure to adjust them correctly afterwards.<\/strong><\/strong><br><strong><strong>These adjustments by the macros do not cover the max_accel and max_accel_to_decel settings, so in this case we always have to adjust them manually.<\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">As you can see, and although they &#8220;sell&#8221; some accelerations and dizzying speeds, the reality is usually quite harsh and they are quite far from them.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We also advise you to adjust these accelerations in your rolling mill so that they are aligned.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"tests-de-impresion-y-uso-de-la-twotrees-sk1\"><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#tests-de-impresion-y-uso-de-la-twotrees-sk1\"><\/a>Printing and usage tests of the TwoTrees SK1<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Once the analysis of the different components of the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;has been carried out, it is time to see how it has behaved during our tests, and although we have already advanced some aspects of its use, we are going to try to give you some extra information that we think is interesting.<\/p>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-8074753\" data-v=\"2\" data-block-id=\"8074753\"><style>.stk-8074753{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-8074753 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-8074753-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-b47c74d\" data-block-id=\"b47c74d\"><style>.stk-b47c74d{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-32a4a54\" data-block-id=\"32a4a54\"><style>.stk-32a4a54 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-32a4a54 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-32a4a54\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-32-a-4-a-54-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-32-a-4-a-54-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-3a6ed87\" id=\"all-the-tests-were-carried-out-with-the-profiles-that-come-with-the-laminator-orca-slicer-in-our-case-for-the-strong-two-trees-sk-1-strong-printer-only-the-temperature-of-the-filament-was-adjusted-to-verify-what-results-we-can-obtain-with-the-default-settings\" data-block-id=\"3a6ed87\"><p class=\"stk-block-heading__text\">All the tests were carried out with the profiles that come with the laminator (OrcaSlicer in our case) for the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;printer, only the temperature of the filament was adjusted to verify what results we can obtain with the default settings.<\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">All the tests were carried out with the profiles that come with the laminator for the&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;printer, only the temperature of the filament was adjusted to verify what results we can obtain with the default settings.&nbsp;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Obviously, we advise, even if the results are correct, to carry out&nbsp;<a href=\"https:\/\/3dwork.io\/o\/kGnwXj5SJwdmHe7JGWZc\/s\/4SOiUz9PiuHFIwg2qk03\/guias-impresion-3d\/calibracion_3d\">calibration tests<\/a>&nbsp;to correctly adjust these values to our taste\/printing conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In our case and for certain filaments we had to make fine adjustments of temperature, flow, retractions and cooling for a correct fit to our&nbsp;<strong>TwoTrees SK1<\/strong>, our filament and our printing conditions.<\/p>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">We start as always by carrying out tests using PLA since with the configuration of our test machine it is the type of filament that would be mostly advised to use, with TPU or PETG we will not have problems either.&nbsp;As always, we use&nbsp;<a href=\"https:\/\/github.com\/SoftFever\/OrcaSlicer\/releases\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>OrcaSlicer<\/strong><\/a>&nbsp;as it has support for our&nbsp;<strong>TwoTrees SK1&nbsp;<\/strong>and is currently our preferred laminator.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter is-resized\"><img loading=\"lazy\" decoding=\"async\" width=\"416\" height=\"373\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-62.png\" alt=\"- - -\" class=\"wp-image-36519\" style=\"width:416px;height:auto\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-62.png 416w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-62-300x269.png 300w\" sizes=\"auto, (max-width: 416px) 100vw, 416px\" \/><figcaption class=\"wp-element-caption\">Filament profiles for the TwoTrees SK1 available from OrcaSlicer<\/figcaption><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">If we go to slightly more technical filaments such as ASA\/ABS in which it is more than advisable to use an enclosure, although in our case and under our tests with ASA we have not had problems, we have to tell you that the machine is prepared to be able to install an enclosure and we have a&nbsp;<a href=\"https:\/\/www.printables.com\/model\/736817-twotrees-sk1-housing-wip\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">project in Printables<\/a>&nbsp;for it all and that probably soon&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">TwoTrees will have it available in its online store<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Going back to the printing tests once the<a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\/twotrees-sk1#instalacion-inicial-twotrees-sk1\">&nbsp;initial installation&nbsp;<\/a>of our&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;was done, we started by launching an OrcaSlicer cube, since this laminator has excellent calibration options with a few simple mouse clicks, the result although it was acceptable showed us some problems to solve.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-437a3624 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FOiRRTRxuiyO83UH7xDfs%252Fimage.png%3Falt=media%26token=de436325-987a-49a4-bd5f-5e9556a60efb&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=b163563307b56fc82d8112a9917760dea65d16ab5349160008b469b85359eb8c\" alt=\"- - -\" width=\"2119\" height=\"876\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">Among the problems detected we saw some punctual jams and some vibrations, this was before carrying out the adjustment process that we explained in previous sections of Klipper improvements, we realized that the issue of jams was caused by the passage of the filament through the PTFE within the guide chain that goes to the head so as we already told you in the analysis of the kinematics we made some modifications to improve that&nbsp;and we didn&#8217;t have that problem again.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Then&nbsp;<strong>we carried out a flow test, Pressure Advance (PA) and extrusion volumetry where we obtained<\/strong>, for the test filament, at<strong>more than 27mm3\/s (for a layer height of 0.2 and line width of 0.4) which gives us a maximum printing speed of just over 300mm\/s<\/strong>&#8230;&nbsp;Remember that this is the maximum in a test piece and should only be used as a reference.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-8c2323d3 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252Fss6XnSnbq7glTgMnCtYh%252Fimage.png%3Falt=media%26token=b2661b54-f9fb-4c96-8d8d-38eea13a47e6&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=8e48abbb0ad3df11746ede4f22abed1d69b3d0547023ce43c459e3d69dcc7527\" alt=\"- - -\" width=\"1303\" height=\"622\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">With all this information obtained&nbsp;<strong>from the tests, we set up our OrcaSlicer base profile for the TwoTrees SK1 and launched several stress tests<\/strong>&nbsp;to see how the results go&#8230;&nbsp;We also make the modifications for vibration calibration explained in the Klipper section of the guide.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In the first of them,&nbsp;<strong>Autodesk FDM Test<\/strong>&nbsp;that we can find directly in OrcaSlicer,&nbsp;<strong>with which we can see the adjustment of several aspects such as the behavior in bridges, cantilevers, mansions, expansion and retractions<\/strong>&#8230;&nbsp;we have to say that<strong>&nbsp;the TwoTrees SK1 after those initial tweaks performed excellently<\/strong>.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-75dcb7c9 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FQOlF0rnzdgLmpY9X9w2S%252Fimage.png%3Falt=media%26token=5b47d8b0-eb20-435b-b972-a6a7ebd06869&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=85c6b23dedebe6ba8dc9bb170fa2f232ac24a026c186f5792ec7f8f3fa2e4d3c\" alt=\"- - -\" width=\"1299\" height=\"645\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">As a second test we launched the<a href=\"https:\/\/www.printables.com\/model\/797493-sensory-fidget-cube\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>&nbsp;Sensory Fidget Cube<\/strong><\/a>, a very complex test to print and that except for expected parts came out decently well and fully functional.&nbsp;The profiles of the laminators at the end are a starting point to be able to adjust them to our machine, filament, printing conditions and needs.&nbsp;As always, we advise you to visit our&nbsp;<a href=\"https:\/\/labs.3dwork.io\/guias-impresion-3d\/calibracion_3d\">calibration guide<\/a>&nbsp;and check out&nbsp;<a href=\"https:\/\/www.printables.com\/@JJR3D\/collections\/115878\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">our collection of Printables with more test prints<\/a>&nbsp;for the fine-tuning of your printer.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-a522839a wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FqCbLHiVUB2E8S2pprse3%252Fimage.png%3Falt=media%26token=74b32c6a-fc03-4da6-a130-64e2385cf9e2&amp;width=768&amp;dpr=4&amp;quality=100&amp;sign=f3377d807f3dccc63a9608daea7b4fe552d8ab4989777f34eda84255550dfa1a\" alt=\"- - -\" width=\"1299\" height=\"569\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-611ed86\" data-v=\"2\" data-block-id=\"611ed86\"><style>.stk-611ed86{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-611ed86 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-611ed86-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-dcf4de8\" data-block-id=\"dcf4de8\"><style>.stk-dcf4de8{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-d95649b\" data-block-id=\"d95649b\"><style>.stk-d95649b .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-d95649b .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-d95649b\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-d-95649-b-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-d-95649-b-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-d8d4495\" id=\"we-recommend-that-after-commissioning-and-initial-calibrations-you-carry-out-maintenance-on-the-machine\" data-block-id=\"d8d4495\"><p class=\"stk-block-heading__text\">We recommend that after commissioning and initial calibrations you carry out maintenance on the machine.<\/p><\/div>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">We will clean with IPA (Isopropyl Alcohol) the linear guides and rods of our shafts and lubricate following&nbsp;<a href=\"https:\/\/www.youtube.com\/watch?v=Azn1x03Abog&amp;list=PL3vFTfhzobPpfoasZ_9hp2DJnNkQieT4L&amp;index=15\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\">the manufacturer&#8217;s instructions in the following video<\/a>, in addition to checking the correct tightening of the screws and anchors.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Depending on the use of the printer, it is advisable to carry out these types of maintenance approximately every 300 hours of use.<\/p>\n<\/div><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">With a base profile adjusted for our needs we carried out some more tests with our&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;to put it to the test, we have to say that it is a very fast, reliable machine and that has left us a good final quality in our prints.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1300\" height=\"872\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92.jpeg\" alt=\"- - -\" class=\"wp-image-36581\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92.jpeg 1300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92-300x201.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92-1024x687.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92-768x515.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92-450x302.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-92-780x523.jpeg 780w\" sizes=\"auto, (max-width: 1300px) 100vw, 1300px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1299\" height=\"235\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90.jpeg\" alt=\"- - -\" class=\"wp-image-36577\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90.jpeg 1299w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90-300x54.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90-1024x185.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90-768x139.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90-450x81.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-90-780x141.jpeg 780w\" sizes=\"auto, (max-width: 1299px) 100vw, 1299px\" \/><\/figure>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1010\" height=\"463\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88.jpeg\" alt=\"- - -\" class=\"wp-image-36573\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88.jpeg 1010w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88-300x138.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88-768x352.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88-450x206.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-88-780x358.jpeg 780w\" sizes=\"auto, (max-width: 1010px) 100vw, 1010px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Although we already explained it previously in the analysis of the&nbsp;<strong>electronics, after a few days of intensive use we found problems of disconnections and random failures in our prints by performing a stress test<\/strong>, due to the experience with other machines with a similar base&nbsp;<strong>we made a modification in the electronics of the print head to improve the cooling of the MCU and the driver of the extrusion system&#8230;&nbsp;With this mod we had no more problems during the rest of the test days with the printer working an average of 12 hours continuously<\/strong>.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"1298\" height=\"261\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87.jpeg\" alt=\"- - -\" class=\"wp-image-36571\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87.jpeg 1298w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87-300x60.jpeg 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87-1024x206.jpeg 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87-768x154.jpeg 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87-450x90.jpeg 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-87-780x157.jpeg 780w\" sizes=\"auto, (max-width: 1298px) 100vw, 1298px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Also, although we also commented on it in the analysis part of the electronics, it is sensational to have a screen to be able to manage the printer directly but we have to say that the implementation of&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;in&nbsp;<strong>the functions and operation in general of the screen leaves a little to be desired with a lack of options<\/strong>, which we do have from the web interface or if we had KlipperScreen,&nbsp;<strong>in addition to many failures in these<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Another aspect to highlight, and quite important depending on the location you have in mind for your printer, is that it&nbsp;<strong>is quite noisy<\/strong>&nbsp;mainly because of the type of kinematics based on linear guides at the speeds it moves and taking into account that it is not a closed printer it can be annoying&#8230;&nbsp;very annoying&#8230;&nbsp;<strong>with an average of 50-60dB at 1m of this, even exceeding 70db at times<\/strong>.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img loading=\"lazy\" decoding=\"async\" width=\"437\" height=\"289\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-85.jpeg\" alt=\"- - -\" class=\"wp-image-36558\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-85.jpeg 437w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-85-300x198.jpeg 300w\" sizes=\"auto, (max-width: 437px) 100vw, 437px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"valoracion-final-twotrees-sk1\">TwoTrees SK1 enclosure kit<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The colleagues from <strong>TwoTrees<\/strong> sent us the great\u00a0<strong>enclosure kit for the TwoTrees SK1<\/strong>\u00a0and that is undoubtedly a more than advisable improvement.<\/p>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-d7840de0 wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/telegram-cloud-photo-size-4-5940670293221687090-y-1024x768.jpg\" alt=\"- - -\" width=\"1024\" height=\"768\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">The\u00a0<strong>kit comes with everything you need to close our TwoTrees SK1<\/strong>\u00a0and\u00a0<strong>improve aspects such as the auxiliary layer ventilation<\/strong>, in our case\u00a0<strong>the kit includes a camera for supervision or timelapses of our prints<\/strong>\u00a0and allows two things that we find more than interesting&#8230;\u00a0<strong>To reduce the noise generated during printing and to be able to print with more technical filaments that require enclosure<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Kit Contents:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Aluminum side and back panels<\/li>\n\n\n\n<li>Tinted crestal top panel and door for an elegant and functional touch<\/li>\n\n\n\n<li>Aluminum profiles for the top<\/li>\n\n\n\n<li>auxiliary fans, one for layer ventilation and one for extraction\/filtering of air from the enclosure<\/li>\n\n\n\n<li>camera, this accessory was included in our kit although they sell the kit without it<\/li>\n\n\n\n<li>screws, tools, etc&#8230;<\/li>\n<\/ul>\n\n\n\n<div class=\"wp-block-uagb-image uagb-block-f4e2348f wp-block-uagb-image--layout-default wp-block-uagb-image--effect-zoomin wp-block-uagb-image--align-none\"><figure class=\"wp-block-uagb-image__figure\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-80-1024x462.png\" alt=\"- - -\" width=\"1024\" height=\"462\" title=\"- -\" loading=\"lazy\" role=\"img\"><\/figure><\/div>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>installation manual comes quite detailed with all the steps and instructions to assemble it<\/strong>, add the auxiliary fans, the enclosure panels and the necessary wiring.<br>In the case of the camera, the instructions were not found in the kit manual, but we have a QR code to access the manual online and it is also very easy to install.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"493\" height=\"326\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82.png\" alt=\"- - -\" class=\"wp-image-37705\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82.png 493w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-300x198.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-82-450x298.png 450w\" sizes=\"auto, (max-width: 493px) 100vw, 493px\" \/><\/figure>\n<\/div>\n\n\n<p class=\"wp-block-paragraph\">Regarding\u00a0<strong>the AI camera, it has Full HD resolution and USB connection<\/strong>.\u00a0<br>It is mounted on the top side profile above the auxiliary layer fan which gives an excellent view of the print area.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In order to take advantage\u00a0<strong>of the functions of this camera, it is necessary that our firmware is at least 2.0.2.21<\/strong>, which is the one that supports the timelapse functionality and related macros.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Little more than leaving you with some photos of how the SK1 turned out after this more than advisable improvement kit.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"306\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-1024x306.png\" alt=\"- - -\" class=\"wp-image-37707\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-1024x306.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-300x90.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-768x229.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-450x134.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83-780x233.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-83.png 1091w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">As we have already told you<strong>, this enclosure kit adds a lot of value to the printer in terms of performance, reliability and why not&#8230;\u00a0aesthetically it looks sensational!!<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">One of the improvements that you will notice with this kit is that<strong>\u00a0the printer is much more robust, and that is noticeable when performing the Input Shaper tests (vibrations)<\/strong>\u00a0that if we accompany it together with anti-vibration feet will improve a little more.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Another aspect that improves is that\u00a0<strong>it is quieter in general,<\/strong>\u00a0obviously using the stock ventilation of the machine&#8230;\u00a0<br><strong>If we use the new auxiliary ventilation we will have levels similar to without enclosure but on the other hand we will improve the layer ventilation with better finishes and print speeds<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Finally,\u00a0<strong>this enclosure allows us to work more comfortably with ASA\/ABS filaments that require enclosure printing conditions<\/strong>.\u00a0The performance of the SK1 in these cases is infinitely better and will allow us to use it in a greater number of projects.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"valoracion-final-twotrees-sk1\">Final review TwoTrees SK1<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The&nbsp;<strong>TwoTrees SK1<\/strong>&nbsp;is focused on a niche market where it will be very difficult to enter taking into account some deficiencies mainly focused on its electronics\/software, as well as the price of the machine that many users probably do not know how to value the quality of construction used in it.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"356\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-1024x356.png\" alt=\"- - -\" class=\"wp-image-36479\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-1024x356.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-300x104.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-768x267.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-450x156.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-780x271.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49.png 1441w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Although&nbsp;<strong>we have a base, chassis\/kinematics and extrusion system, excellent, this is overshadowed by the implementation of Klipper<\/strong>&nbsp;where you could get more functions or at least the freedom to have access to them if you use an official version.&nbsp;And&nbsp;<strong>the same with the electronics, which although it has behaved better than in other similar analyzed machines, we believe that it is not a base at the height of the overall quality of the machine<\/strong>.&nbsp;And seeing the source of these problems, we are afraid that even if&nbsp;<a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;makes efforts to improve it, it will be difficult to have a machine where the word Klipper truly acquires its meaning of powerful, versatile firmware and that, thanks to its continuous improvements, gives us more functionalities to improve the use and reliability of our machine.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"188\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-1024x188.png\" alt=\"- - -\" class=\"wp-image-36481\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-1024x188.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-300x55.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-768x141.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-450x82.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50-780x143.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-50.png 1441w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><strong><strong><strong>Manufacturers in general without talking specifically about&nbsp;<\/strong><a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a><strong>, either because of the possibilities or because of fashion, are making the leap to Klipper and this is something that has its advantages and disadvantages for both manufacturers and users.<\/strong><\/strong><\/strong><\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"216\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-1024x216.png\" alt=\"- - -\" class=\"wp-image-36485\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-1024x216.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-300x63.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-768x162.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-450x95.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52-780x165.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-52.png 1441w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>From the manufacturer&#8217;s side, they want to have control to minimize problems with their machines since a low-level control such as Klipper provides, which on the one hand is an advantage, can turn into a disaster in certain scenarios such as users without a Klipper base or trying to change configurations<\/strong>&#8230;&nbsp;And in the end, the normal thing is not to think that it is our fault as a user but to complain to the manufacturer.&nbsp;But&nbsp;<strong>on the part of the medium\/advanced users who see how their powerful machines are limited in functions that they could have and depend on the manufacturer to give good support and follow-up to their Klipper implementations,<\/strong>&nbsp;something that in the medium\/long term and due to the experience of many years we doubt that it will be so.&nbsp;<strong>Sticking with a very capable machine, limited and outdated in options with respect to what it could have<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">With all this,&nbsp;<strong>the performance and print quality during our tests have been very good<\/strong>, although far from the &#8220;marketing&#8221; numbers of 700mm\/s we have been able&nbsp;<strong>to print approximately 300mm\/s the fill of our tests and normally 60% of that speed is what we apply to external perimeters<\/strong>.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"457\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-1024x457.png\" alt=\"- - -\" class=\"wp-image-36483\" title=\"- -\" srcset=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-1024x457.png 1024w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-300x134.png 300w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-768x343.png 768w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-450x201.png 450w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51-780x348.png 780w, https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-51.png 1440w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">An aspect that we would also like to highlight is&nbsp;<strong>the support of several laminators with a base profile that can make our lives much easier when it comes to having the freedom to choose the one that best suits our needs<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For all the above reasons, I think it is a perfect machine for two types of users&#8230;&nbsp;the one who just wants to print as the machine comes and hope that&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;continues to improve the overall experience related to the software part&#8230;&nbsp;and that advanced user who is looking for a machine with a very good base (again talking about the chassis\/kinematics\/extrusion) and who in the long run decides to improve the Klipper part either with unofficial updates (if these are not provided by TwoTress in the medium\/long term) or directly by making a change in the electronics.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"donde-comprar-la-twotrees-sk1\">Where to buy the TwoTrees SK1?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/twotrees3d.com\/\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>TwoTrees<\/strong><\/a>&nbsp;has an online store on their website where you can&nbsp;<a href=\"https:\/\/www.twotrees3dofficial.com\/de\/products\/sk1-corexy-3d-printer-twotrees\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><strong>buy directly the TwoTrees SK1 and its accessories\/spare parts<\/strong><\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In any case, we provide you with some links to other stores for reference:<\/p>\n\n\n\n<figure class=\"wp-block-table is-style-regular\"><table><tbody><tr><td><strong>TwoTrees SK1<\/strong><\/td><td><img decoding=\"async\" src=\"https:\/\/labs.3dwork.io\/~gitbook\/image?url=https:%2F%2F3760761605-files.gitbook.io%2F%7E%2Ffiles%2Fv0%2Fb%2Fgitbook-x-prod.appspot.com%2Fo%2Fspaces%252F4SOiUz9PiuHFIwg2qk03%252Fuploads%252FXUs1eaGRV2QIOMu8J6LN%252Fimage.png%3Falt=media%26token=3731e6f3-06b3-4915-ba79-b731a63020f7&amp;width=300&amp;dpr=4&amp;quality=100&amp;sign=fd0ba994fe4f012b2a5a29069c8f0abd329fc3e94ca6a4f8f376b2b5248b7ae2\" alt=\"- - -\" style=\"width: 90px;\" title=\"- -\"><\/td><td><a href=\"https:\/\/s.click.aliexpress.com\/e\/_DmVQrFX\" target=\"_blank\" rel=\"noopener nofollow\" class=\"external\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-53.png\" alt=\"- - -\" title=\"- -\"><\/a><\/td><td><a href=\"https:\/\/www.twotrees3dofficial.com\/de\/products\/sk1-corexy-3d-printer-twotrees\" target=\"_blank\" rel=\"noopener nofollow\" class=\"external\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-54.png\" alt=\"- - -\" title=\"- -\"><\/a><\/td><\/tr><tr><td><strong>TwoTrees SK1<\/strong><br><strong>Enclosure kit<\/strong><\/td><td><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-84.png\" alt=\"- - -\" style=\"width: 100px;\" title=\"- -\"><\/td><td><a href=\"https:\/\/s.click.aliexpress.com\/e\/_Dmmflfd\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-53.png\" alt=\"- - -\" title=\"- -\"><\/a><\/td><td><a href=\"https:\/\/www.twotrees3dofficial.com\/collections\/for-sk1\/products\/two-trees-enclosure-kit-for-sk1\" target=\"_blank\" rel=\"noreferrer noopener nofollow\" class=\"external\"><img decoding=\"async\" src=\"https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-54.png\" alt=\"- - -\" title=\"- -\"><\/a><\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-d6d450a\" data-v=\"2\" data-block-id=\"d6d450a\"><style>.stk-d6d450a{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-d6d450a .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-d6d450a-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-3fdc88d\" data-block-id=\"3fdc88d\"><style>.stk-3fdc88d{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-bf46fd6\" data-block-id=\"bf46fd6\"><style>.stk-bf46fd6 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-bf46fd6 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#0693e3 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-bf46fd6\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-bf-46-fd-6-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-bf-46-fd-6-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 512 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M256 8C119.043 8 8 119.083 8 256c0 136.997 111.043 248 248 248s248-111.003 248-248C504 119.083 392.957 8 256 8zm0 110c23.196 0 42 18.804 42 42s-18.804 42-42 42-42-18.804-42-42 18.804-42 42-42zm56 254c0 6.627-5.373 12-12 12h-88c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h12v-64h-12c-6.627 0-12-5.373-12-12v-24c0-6.627 5.373-12 12-12h64c6.627 0 12 5.373 12 12v100h12c6.627 0 12 5.373 12 12v24z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-8260cff\" id=\"if-you-use-the-shopping-links-the-price-of-the-product-will-be-the-same-as-if-you-access-it-regularly-but-strong-3-d-work-will-have-a-small-commission-left-strong-br-something-that-will-help-us-support-the-project-and-continue-generating-content\" data-block-id=\"8260cff\"><p class=\"stk-block-heading__text\">If you use the shopping links, the price of the product will be the same as if you access it regularly, but&nbsp;<strong>3DWork will have a small commission left<\/strong>.<br>Something that will help us support the project and continue generating content.<\/p><\/div>\n<\/div><\/div>\n<\/div><\/div>\n\n\n\n<div class=\"wp-block-stackable-icon-box stk-block-icon-box stk-block stk-79a3cc6\" data-v=\"2\" data-block-id=\"79a3cc6\"><style>.stk-79a3cc6{padding-top:0px !important;padding-right:0px !important;padding-bottom:0px !important;padding-left:0px !important}.stk-79a3cc6-container{background-color:#fff6f0 !important}.stk-79a3cc6-container:before{background-color:#fff6f0 !important}.stk-79a3cc6 .stk-block-icon-box__content{padding-top:16px !important;padding-right:16px !important;padding-bottom:16px !important;padding-left:16px !important}<\/style><div class=\"stk-block-content stk-inner-blocks stk-block-icon-box__content stk-container stk-79a3cc6-container stk-hover-parent\">\n<div class=\"wp-block-stackable-icon-label stk-block-icon-label stk-block stk-29a585b\" data-block-id=\"29a585b\"><style>.stk-29a585b{margin-bottom:0px !important}<\/style><div class=\"stk-row stk-inner-blocks stk-block-content\">\n<div class=\"wp-block-stackable-icon stk-block-icon has-text-align-left stk-block stk-8a30750\" data-block-id=\"8a30750\"><style>.stk-8a30750 .stk--svg-wrapper .stk--inner-svg svg:last-child,.stk-8a30750 .stk--svg-wrapper .stk--inner-svg svg:last-child :is(g,path,rect,polygon,ellipse){fill:#ff6900 !important}<\/style><span class=\"stk--svg-wrapper\"><div class=\"stk--inner-svg\"><svg style=\"height:0;width:0\"><defs><linearGradient id=\"linear-gradient-8a30750\" x1=\"0\" x2=\"100%\" y1=\"0\" y2=\"0\"><stop offset=\"0%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-8-a-30750-color-1)\"><\/stop><stop offset=\"100%\" style=\"stop-opacity:1;stop-color:var(--linear-gradient-8-a-30750-color-2)\"><\/stop><\/linearGradient><\/defs><\/svg><svg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" viewBox=\"0 0 576 512\" aria-hidden=\"true\" width=\"32\" height=\"32\"><path d=\"M569.517 440.013C587.975 472.007 564.806 512 527.94 512H48.054c-36.937 0-59.999-40.055-41.577-71.987L246.423 23.985c18.467-32.009 64.72-31.951 83.154 0l239.94 416.028zM288 354c-25.405 0-46 20.595-46 46s20.595 46 46 46 46-20.595 46-46-20.595-46-46-46zm-43.673-165.346l7.418 136c.347 6.364 5.609 11.346 11.982 11.346h48.546c6.373 0 11.635-4.982 11.982-11.346l7.418-136c.375-6.874-5.098-12.654-11.982-12.654h-63.383c-6.884 0-12.356 5.78-11.981 12.654z\"><\/path><\/svg><\/div><\/span><\/div>\n\n\n\n<div class=\"wp-block-stackable-heading stk-block-heading stk-block-heading--v2 stk-block stk-8b6ceee\" id=\"strong-strong-strong-strong-strong-strong-strong-about-our-product-review-methodology-strong-strong-strong-strong-strong-strong-strong\" data-block-id=\"8b6ceee\"><p class=\"stk-block-heading__text\"><strong><strong><strong><strong><strong><strong><strong>ABOUT OUR PRODUCT REVIEW METHODOLOGY<\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/strong><\/p><\/div>\n<\/div><\/div>\n\n\n\n<div class=\"wp-block-stackable-text stk-block-text stk-block stk-0bc9426\" data-block-id=\"0bc9426\"><style>.stk-0bc9426{border-top-left-radius:0px !important;border-top-right-radius:0px !important;border-bottom-right-radius:0px !important;border-bottom-left-radius:0px !important;overflow:hidden !important;margin-bottom:0px !important}<\/style><p class=\"stk-block-text__text\">This&nbsp;<strong>review of the TwoTrees SK1 was made with a machine provided by TwoTrees<\/strong>.<\/p><\/div>\n\n\n\n<div class=\"wp-block-stackable-text stk-block-text stk-block stk-b4ca971\" data-block-id=\"b4ca971\"><style>.stk-b4ca971{margin-bottom:0px !important}<\/style><p class=\"stk-block-text__text\"><strong><strong><strong><strong><strong>TwoTrees provided us with such a printer without influencing the content in any way.&nbsp;Our evaluation and observations are entirely based on our experience of the testing of the product during the testing period used to ensure that we provide an accurate evaluation of the product.<\/strong><\/strong><\/strong><\/strong><\/strong><\/p><\/div>\n\n\n\n<p class=\"wp-block-paragraph\"><strong><strong><strong>At 3Dwork we are always transparent and honest in our product reviews to ensure that our audience can trust the content we produce.<\/strong><\/strong><\/strong><a href=\"https:\/\/labs.3dwork.io\/reviews-guias\/impresoras-3d\/fdm\/twotrees\"><\/a><\/p>\n<\/div><\/div>\n","protected":false},"excerpt":{"rendered":"<p>Our colleagues at&nbsp;TwoTrees&nbsp;have launched a very interesting new printer, the&nbsp;Twotrees SK1. TwoTrees&nbsp;is an old acquaintance in the 3D world, created in 2017 and launching its first 3D printer in 2018.&nbsp;In addition,&nbsp;TwoTrees&nbsp;diversified its range of solutions back in 2020 by introducing the TT series of desktop diode laser engraving, which&nbsp;we could already see in our workshop&nbsp;some [&hellip;]<\/p>\n","protected":false},"author":6,"featured_media":36480,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_uag_custom_page_level_css":"","footnotes":""},"categories":[6084,3702,6458,3223],"tags":[5832,4360,6478],"class_list":["post-36495","post","type-post","status-publish","format-standard","has-post-thumbnail","category-3d-printers-en","category-articles","category-fdm-en","category-reviews","tag-klipper-en","tag-review-en-2","tag-twotrees-en"],"uagb_featured_image_src":{"full":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49.png",1441,501,false],"thumbnail":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-150x150.png",150,150,true],"medium":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-300x104.png",300,104,true],"medium_large":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-768x267.png",768,267,true],"large":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-1024x356.png",1024,356,true],"1536x1536":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49.png",1441,501,false],"2048x2048":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49.png",1441,501,false],"pixwell_370x250":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-370x250.png",370,250,true],"pixwell_370x250-2x":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-740x500.png",740,500,true],"pixwell_370x250-3x":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-1110x501.png",1110,501,true],"pixwell_280x210":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-280x210.png",280,210,true],"pixwell_280x210-2x":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-560x420.png",560,420,true],"pixwell_400x450":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-400x450.png",400,450,true],"pixwell_400x600":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-400x501.png",400,501,true],"pixwell_450x0":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-450x156.png",450,156,true],"pixwell_780x0":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49-780x271.png",780,271,true],"pixwell_780x0-2x":["https:\/\/3dwork.io\/wp-content\/uploads\/2024\/03\/image-49.png",1441,501,false]},"uagb_author_info":{"display_name":"JJR","author_link":"https:\/\/3dwork.io\/en\/author\/juanjo\/"},"uagb_comment_info":5,"uagb_excerpt":"Our colleagues at&nbsp;TwoTrees&nbsp;have launched a very interesting new printer, the&nbsp;Twotrees SK1. TwoTrees&nbsp;is an old acquaintance in the 3D world, created in 2017 and launching its first 3D printer in 2018.&nbsp;In addition,&nbsp;TwoTrees&nbsp;diversified its range of solutions back in 2020 by introducing the TT series of desktop diode laser engraving, which&nbsp;we could already see in our workshop&nbsp;some&hellip;","_links":{"self":[{"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/posts\/36495","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/users\/6"}],"replies":[{"embeddable":true,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/comments?post=36495"}],"version-history":[{"count":0,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/posts\/36495\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/media\/36480"}],"wp:attachment":[{"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/media?parent=36495"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/categories?post=36495"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/3dwork.io\/en\/wp-json\/wp\/v2\/tags?post=36495"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}